Devantech dS2824 Скачать руководство пользователя | Manualshive

Страница: 21 / 64

background image

dS2824

dS2824

User Manual v4.09

Input/Output configuration

The I/O Names tab is used to assign meaningful names to the I/O terminals.

As with relay names these may be up to 20 characters long, but do check it looks ok on a mo-

bile device or whatever you are using to control the module.

Click on the drop down box selection tab to select the I/O type.
The two digital modes are the same except for “Digital No-Pullup” the passive pull-up resistor

is turned off and for “Digital With Pullup” it is turned on.
The no-pullup option is useful for connecting to digital circuits (3.3v or 5v) that supply the in-

put voltage. The with pullup option turns on a weak pull up to 12v (actually nearer 7-8v be-
cause of the input design). This is useful for directly connecting volt free contacts such as relay

contacts or switches. They are connected between the pin (P) and ground (0v).
To use as inputs, make sure the output drive is off or the NPN transistor will drive the output

low. The NPN transistor can sink about 100mA.

The analogue modes convert the input volts to a digital number in the range 0-4095 (12-bit
conversion). The input voltage range is selectable for 4.096v (Analog Ref4) and 5v (Analog

Ref5).

Copyright

© 2016-2021,

Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

21

«
...
19
20
21
22
23
...
»

Содержание dS2824

































































Отзывы:

Нет отзывов

Похожие инструкции для dS2824

Бренд: Ytc Страницы: 10

Бренд: CD Automation Страницы: 8

Бренд: CD Automation Страницы: 53

Бренд: ABB Страницы: 68

2CDC 113 016 M9701

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 12

Бренд: ABB Страницы: 42

Бренд: ABB Страницы: 12

CIRCUIT SHIELD 237F Series

Бренд: ABB Страницы: 15

Бренд: ABB Страницы: 24

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 25

Бренд: ABB Страницы: 10

Бренд: ABB Страницы: 22

Бренд: ABB Страницы: 8

Бренд: ABB Страницы: 12

Бренд: ABB Страницы: 12

Бренд: ABB Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды