Devantech dS2824 Скачать руководство пользователя | Manualshive

Страница: 18 / 64

background image

dS2824

dS2824

User Manual v4.09

Relay automation

There are a set of control boxes that provide for autonomous relay operation. If you just want
to control the relays from the webpage or using one of the TCP/IP modes, then leave these

boxes blank.

Relay No. box
This selects the relay you wish to configure. There are 32 relays available. The first 24 relays

are the actual relays on the module. Relays 25-32 are virtual relays. They have no physical
presence but otherwise behave identically to the real ones. They can provide additional pro-

cessing and a larger control surface to your application.

Pulse/Follow box
If you place a number in this box then that is the pulse time for the relay in mS (1000mS = 1

second). The minimum value is 100mS. The maximum is 2147483647 (more than 24 days).
When the relay is toggled on, timing begins and at the end of the time period the relay goes

off again. If the button is pressed again during timing then the timing is restarted.

The above example will turn off the yard lights after 30 minutes. 1800000 mS is 1800 seconds.
1800 seconds is 30 minutes.

It also possible to insert a boolean equation into the box. Boolean equations are just simple

equations that evaluate to a 0 or 1.
For example Relay 1 is referred to a R1. Input1 is referred to as D1 (Digital 1). Analogue input

1 is referred to as A1.

Copyright

© 2016-2021,

Devantech Ltd.

All rights reserved.

www.robot-electronics.co.uk

18

«
...
16
17
18
19
20
...
»

Содержание dS2824

































































Отзывы:

Нет отзывов

Похожие инструкции для dS2824

Бренд: GE Digital Energy Страницы: 160

Бренд: ZIEHL Страницы: 8

Бренд: ZIEHL Страницы: 8

Бренд: ZIEHL Страницы: 12

Бренд: Sven Страницы: 8

Бренд: Viega Страницы: 3

Бренд: Bitron Video Страницы: 2

Бренд: Eaton Страницы: 16

Бренд: TE Connectivity Страницы: 4

Бренд: Keithley Страницы: 4

Бренд: Patton Страницы: 170

Бренд: GE Страницы: 175

Бренд: ABB Страницы: 40

Бренд: ASO Safety Solutions Страницы: 28

Бренд: GE Страницы: 36

Бренд: F&F Страницы: 7

Бренд: Signet Страницы: 4

Бренд: Broyce Control Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды