Denso QB30-SR, Руководство пользователя

Страница: 127 / 139

Setting command Transmitted command Response
Data output timing
(Change) WR11#n
(Confirmation) RD11 OK n=0: Synchronous
n n=1: Asynchronous
Non-scan code
(Change) WR12#n
(Confirmation) RD12 OK n=0: Enabled
n n=1: Disabled
Indirect mode
one-shot time (Change) WR15#nn
(Confirmation) RD15 OK nnn=010 - 999
nnn (0.1 - 9.99 sec.)
Trigger signal input
delay time
(Change) WR16#nnn
(Confirmation) RD16 OK nnn=000 – 004 (No Delay time)
nnn=005
～
999 (5ms
～
999ms)
Signals output
ON duration width (Note
3) (Change) WR17#nnn
(Confirmation) RD17 OK nnn=001 - 255
nnn (10 to 2550 ms)
Single output Delay time
(Note 3)
(Change) WR18#nn
(Confirmation) RD18 OK nn=00 – 99 (no Delay time)
nn= 01-99 (0.1 - 9.9 sec.)
non-scan code
(Change) WR19#hhhhhhh
(Confirmation) RD19 OK hhhhhhh=Non-scan code
hhhhhhh (Up to seven characters) (Not2)
Scanning start command
(Change) WR1A#hhhhhhh
(Confirmation) RD1A OK hhhhhhh=ON code setting
hhhhhhh (Up to seven characters)(Note 2)
Scanning end command
(Change) WR1B#hhhhhhh
(Confirmation) RD1B OK hhhhhhh=OFF code setting
hhhhhhh (Up to seven characters) (Note 2)
LED lighting on control
setting (Note1)
(Change) WR1C#nn
(Confirmation) RD1C
OK n ＝ 0 ： Always off
n n ＝ 1 ： Automatic
n ＝ 2 ： Always on
Decode time setting
(Note 1)
(Change) WR1D#nnn
(Confirmation) RD1D OK nnn=000: Disabled
(No decode time setting)
nnn nnn=005 - 999 (0.05 - 9.99 sec.)
Note 1: NG to indicate the scanning failure is output when decoding is unsuccessful during the setting time because
the scanner repeats the decode within readable code setting the upper limit of decode limit when scanning test
is performed. Effective only when Continuous reading mode A, Continuous reading mode B or auto sense
mode is selected.
Note 2: 0x20 ～ 0x7E excluding ASCII character can be registered.
Note 3 The setting is effective only for OK signal, NG signal, verification OK signal or verification NG signal.
Setting command Transmitted command Response
Output terminal 1 setting
(Change) WR1E#n
(Confirmation) RD1E OK n
＝
0
：
Unused
n n
＝
1
：
OK signal output
n ＝ 2 ： NG signal output
n ＝ 3 ： Verification OK signal output
n ＝ 4 ： Verification NG signal output
n ＝ 5 ： READY signal output
Output terminal 1 setting
(Change) WR1G#n
(Confirmation) RD1G OK n ＝ 0 ： Unused
n n ＝ 1 ： OK signal output
n ＝ 2 ： NG signal output
n
＝
3
：
Verification OK signal output
n
＝
4
：
Verification NG signal output
n
＝
5
：
READY signal output
n
＝
6
：
SHT signal output
116