Denon AirPlay AVR-4311CI, Руководство пользователя

Страница: 13 / 158

10
ENGLISH
11
2QWKH
STEP3
VFUHHQXVH ui
WRVHOHFW³1H[W o &DOFXODWLRQ´DQG
WKHQSUHVV
ENTER
Measuring results are analyzed, and the
frequency response of each speaker in the
listening room is determined.
$8'<66(<$8726(783
67(3&DOFXODWLRQ
1RZFDOFXODWLQJ3OHDVHZDLW
• Analysis takes several minutes to complete. The
time required for this analysis depends on the
number of speakers connected.
The more connected speakers there are, the
longer it takes to perform analysis.
Set up speakers (Audyssey® Auto Setup)
STEP 4
Calculation
STEP 5
Check
12
8VH ui WRVHOHFWWKHLWHP\RXZDQW
WRFKHFNDQGWKHQSUHVV
ENTER
$8'<66(<$8726(783
5(7851
1H[W6WRUH
6HOHFWLWHPWRFKHFN
(QWHU &DQFHO
&URVVRYHU&KHFN
&K/HYHO&KHFN
'LVWDQFH&KHFN
6SNU&RQILJ&KHFN
67(3&KHFN
&KHFNSURFHVVLQJUHVXOWV
7RSURFHHGSUHVV´1H[Wµ
• Subwoofers may measure a greater reported
distance than the actual distance due to added
electrical delay common in subwoofers.
• If you want to check another item, press
RETURN
.
13
8VH ui WR VHOHFW ³1H[W o 6WRUH´
DQGWKHQSUHVV
ENTER
14
6HOHFW³6WRUH´DQGWKHQSUHVV
ENTER
Save the measurement results.
$8'<66(<$8726(783
67(36WRUH
1RZVWRULQJ3OHDVHZDLW
$8'<66(<$8726(783
5(7851
$SSO\DQGVWRUHPHDVXUHPHQWUHVXOW
(QWHU &DQFHO
6WRUH
67(36WRUH
3UHVV´6WRUHµWRVWRUHFDOFXODWLRQUHVXOWV
• Saving the results requires about 20 seconds.
• If the measuring results are not to be saved,
press
RETURN
. A message “Cancel auto
setup?” will be displayed. Press
o
then select
“Yes”. All the measured Audyssey Auto Setup
data will be erased.
NOTE
During saving of measurement results, be sure
not to turn off the power.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confi rm the setting Return to previous menu
NOTE
• If the result differs from the actual connection
status, or if “Caution!” is displayed, see “Error
messages” (
v
page 11). Then carry out Audyssey
Auto Setup again.
• If the result still differs from the actual connection
status after remeasurement or the error message
still appears, it is possible that the speakers
are not connected properly. Turn this unit off,
check the speaker connections and repeat the
measurement process from the beginning.
• If you change speaker positions or orientation,
perform Audyssey Auto Setup again to fi nd the
optimal equalizer settings.
STEP 6
Store
Finish
15
8QSOXJ WKH VHWXS PLFURSKRQH IURP
WKHXQLW¶V6(7830,&MDFN
16
6HW'\QDPLF9ROXPHŠ
$8'<66(<$8726(783
1R
<HV
7XUQ'\QDPLF9ROXPHRQDQGH[LW$XWR6HWXS
([LW
)LQLVK
6WRULQJFRPSOHWH
$XWR6HWXSLVQRZILQLVKHG
3OHDVHXQSOXJPLFURSKRQH
7XUQRQ'\QDPLF9ROXPH"
• For details of Dynamic Volume settings, see
page 90.
n
When turning Dynamic Volume on
Use
u
to select “Yes“, and then press
ENTER
.
• The unit automatically enters “Evening” mode.
n
When turning Dynamic Volume off
Use
i
to select “No“, and then press
ENTER
.
NOTE
• After performing Audyssey Auto Setup, do not
change the speaker connections or subwoofer
volume. In event of a change, perform Audyssey
Auto Setup again.
• After performing Audyssey Auto Setup with two
subwoofers, do not change the channel distances
and levels of both subwoofers.