Denison Hydraulics P07 C-mod Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 80

Denison Hydraulics P07 C-mod Скачать руководство пользователя страница 28

PRESSURE COMPENSATOR CONTROL

28

COMPENSATOR DISASSEMBLY

1.

See Figure 6.

Back off maximum volume screw or handwheel to full displacement. Remove maximum volume screw

or handwheel assembly.

2. Remove bolts holding cap to pump.
3. Remove plug (15) and attached parts. Remove spring (11) and spool (18).
4. Remove adjusting plug (2) and attached parts. Remove seal piston (5). Note: a 10-24 screw may be used to assist in

pulling the piston. Remove spring (7) and cone (8).

5. Do not remove sleeve in body (1). Sleeve is pressed into cap and finished to size. If sleeve or cap is worn, replace

the cap-sleeve assembly (1).

6. Examine seat (10) for wear. Do not remove unless damaged.

ASSEMBLY

See page 26 for tightening torque on plugs

1. Install Avseal plugs (9) and .047”, 1,19 mm. orifice (19) in body.
2. Press seat (10) into bore squarely against shoulder in bore.
3. Install spool (18) into bore as shown. Install spring (11) over end of spool. Install O-ring (6) on seal piston (16).

Lubricate and install into plug (15). Install plug (15) into cap. Install screw (3), nut (4) and plastic cap (17).

4. Install O-ring (6) on seal piston (5).
5. Lubricate O-ring and install cone (8), spring (7) and seal piston into bore in cap (1), being careful that cone enters seat

(10). Install remaining parts. Torque plugs (12) and (21)

6. Note proper location for cap on pump (pg. 24). Install O-rings on interface between cap and pump control pad.
7. Install cap on pump control pad, guiding the control piston into the bore. Install maximum volume stop assembly.
8. Torque mounting bolts to 75 lbs.• ft., 102 N m.

www.comoso.com

«
...
26
27
28
29
30
...
»

Содержание P07 C-mod

















































































Отзывы:

Нет отзывов