manualshive.com logo in svg

Denison Hydraulics P07 C-mod, Информация о сервисе, Страница: 20 / 80

Поделиться
Скачать
Denison Hydraulics P07 C-mod Скачать руководство пользователя страница 20

PUMP REASSEMBLY INSTRUCTIONS

20

4. Press bearing outer race (11) into housing (7).

BARREL AND INNER RACE ASSEMBLY

5.

Thread seven M8-1,25 studs into bearing inner race. Lower barrel (14) 
over studs and seat. If the inner race is heated to 150

0

F, 65

0

C, barrel will 

slide into position without force. If race is not heated, longer screws (12) 
can be used to draw the race and barrel together. Insert screws (12) and 
torque to 30 lbs ft., 40 Nm. 

See illustration

6.

Apply oil to face of port plate and inner bearing race.  Attach tool T-1 to 
barrel with two M6 screws. Carefully lower barrel assembly into housing 
engaging inner race into rollers of outer bearing race, barrel may then be 
lowered until it has seated on port plate.

7.

Insert two "O" rings (27) into each retainer (28).  Apply thread locking 

compound to two screws (26) and secure retainer to housing. Torque to 84 lbs-in., 9,5 Nm.

8. Apply thread locking compound to two screws (26) and assemble the other retainer on opposite side of housing. 

Torque to 84 lbs-in.,  9,5 Nm.

9. Assemble the two piston rings (39) on control piston (44).  Insert control piston (44) into housing bore that is used 

with the control caps. 

For CW shaft rotation

, the long end of the piston must be positioned to the right. 

(Ref. fig.1

)

For CCW rotation

, the long end of the piston is to the left.

10. Position Belleville washers (18) on barrel, 

See illustration. 

To insure proper pump opera-

tion and correct barrel holddown force they must be assembled exactly as shown.  Place 
barrel stop (19) on Belleville washers and center the washers and stop on barrel.

CAM ASSEMBLY

11. Set cam assembly (10) on suitable surface protecting cam surfaces from damage during 

assembly. 

See illustration

12. Place wear plate (22) on cam.
13. Position pistons-shoes-retainer assembly (17) over center post and against wear plate.
14. Install thrust washer (45) over center post.
15. Six different retainers (46) are available for setting the shoe holddown.  Each retainer is

marked: 

white dot

.062", 1,57 mm thick, 

red dot

.064", 1,63 mm thick, 

green dot

.067",

1,70 mm thick, 

yellow dot

.069", 1,75 mm thick,  and 

blue dot

.071", 1,80 mm thick.  Install the thickest retainer 

with the dot side up,

that will fit in the groove on the center post and allow a clearance of .003"-.005", 

0,076-0,127 mm between the shoe and wear plate.  

A .003", 0,076 mm feeler gage must go

completely under 

any shoe, and a 

.005”, 0,127 mm feeler gage must not go

under any 

shoe while holding a piston and lifting tightly against the shoe retainer.  
The piston and shoe assembly must be free to rotate easily by hand. 
Rotate 360o to confirm there is no binding and that each shoe is free in 
the retainer plate. Oil the assembly thoroughly.

16. Install slide link (43) on rocker cam pin as shown. 
17. Oil barrel bores before installing cam assembly.    The piston must be 

moved outward 

(away from pump center)

so that clearance is provided for

installing the rocker cam assembly.  Lower cam assembly into the housing
with the slide link positioned so it will engage into the control piston (44).  
The seven pistons (17) must first be engaged into the barrel bores.  
Next the slide link (43) must engage into the control piston (44).  Continue 
lowering rocker cam assembly until it is seated on cam/bearing retain-
ers(28).

18. Apply thread locking compound to two screws (34) and assemble clear-

ance-bearing (24) to cam-bearing retainer (28) using the screws (34), two 
washers (25) and two washers (23).  Move rocker cam to the right until it 
is against stop. 

Set clearance

between clearance bearing (24) and cam at

.006", 0,152 mm. Torque screws to 6 lbs-ft., 8,1 Nm maintaining the .006",
0,152 mm clearance.

19.Adjust piston (44) toward the 

off stroke

control side (31). This will place the cam at 

approximately zero displacement and provide clearance for the shaft installation.

18

19

.005/.003” (,127/,076 mm)
SHOE CLEARANCE

17

46

45

22

10

43

24

www.comoso.com

Содержание P07 C-mod

















































































Отзывы:

Нет отзывов