Denison Hydraulics P07 C-mod Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 80

Denison Hydraulics P07 C-mod Скачать руководство пользователя страница 22

- Continued -

Rocker cradle assembly

20.Apply thread locking compound to two screws (47) and assemble two cam bearings (42) to cradle (6). Torque to 33

lbs-in., 3,8 Nm.

21. Press bearing (1b) on shaft (1a). Press on inner race only.
22. Apply over 360o bead of gasket sealant to seal retainer (1e) per following sketch. Press shaft seal (1c) into seal

retainer (1e).

23. Install shaft seal and retainer on shaft using Tool T-3 to protect seal.
24. Install "O" ring (5) in cradle (6).
25. Press seal retainer and bearing and shaft assembly into bore of cradle (6)

using Tool T-2.

26. Install snap ring (4) to cradle.
27. Install "O" ring (8) to rocker cradle.

28. Install retaining ring (20) on shaft.
29. Center Belleville washers and barrel stop. Lower rocker cradle assembly

into pump housing with the step in the rocker cradle correctly positioned
so that clearance is provided for slide link (43). The threaded hole in the
end of shaft should be used to support the assembly. SAE shafts use
3/8-16 threads, ISO shafts use M10 threads, DIN shafts use M12
threads. The shaft spline must first engage the splined barrel stop (19),
thru the Belleville washers (18) and engage the barrel spline. The
assembly will then rest on the cam.

30. Install socket head cap screws (9) as shown. Torque evenly to 57 ft-lb

(77 Nm). Install case drain plug (49) and shipping plug (51). If pump
does not contain displacement indicator, install plug (52) and “O” ring
(53) in indicator hole.

INDICATOR ASSEMBLY OPTION

See figure 2.

To install indicator assembly, loosen setscrew (6), remove indicator

(2) and slide shaft out of nut (1). Guide fork into indicator hole in housing to
engage the pin on the hanger. a 1/4-20 SHCS or threaded rod may be used to
hold the shaft. Slide nut (1) over shaft and tighten nut in threaded hole. Pull
shaft out to slip retaining ring (9) into groove in shaft. Use maximum volume
stop to set pump on zero displacement (10.2 turns from full). Install indicator,
set pointer on “0” and lock in position.

PUMP REASSEMBLY INSTRUCTIONS

22

ref. Figure 2

Indicator assembly

THREAD LOCK-

ING COMPOUND
33 IN-LB, 3,8 Nm

apply

thread

locking

compound

6

42

47

www.comoso.com

«
...
20
21
22
23
24
...
»

Содержание P07 C-mod

















































































Отзывы:

Нет отзывов