Delta IFD9503 Скачать руководство пользователя страница 9

Страница: 9 / 57

CANopen Slave Communication Module IFD9503

DVP-PLC Application Manual

PIN 8

PIN 7

PIN 6

Baud rate

Off On Off

50k

bps

Off On On

125k

bps

On Off Off

250k

bps

On Off On

500k

bps

On On Off

800k

bps

On On On

bps

Note:

The changed setting of the baud rate of CANopen is only valid when IFD9503 is re-powered. When

IFD9503 is operating, changing the baud rate will be invalid.

2.5

Communication Ports on IFD9503

The communication ports on IFD9503 are used for the connection the

equipment (Delta programmable logic controller, Delta AC motor drive,

Delta temperature controller, Delta servo drive, Delta human machine

interface and custom equipment).

PORT1

PORT2

1. PORT 1 PIN definition:

PORT 1 sketch

Description

1 N.C.

2 GND

3 DATA-

4 DATA+

5 N.C.

PORT1

6 N.C.

Note:

PORT 1 supports RS-485 communication only.

2. PORT 2 PIN definition:

PORT2 sketch

RS-232

RS-485

1 N.C.

N.C.

2 RXD

N.C.

3 TXD

DATA-

4 N.C.

N.C.

5 GND

N.C.

6 N.C.

N.C.

7 N.C.

N.C.

8 N.C.

DATA+

1
6
2

3
8
4
9
5

DB9 male

9 N.C.

N.C.

Note:

PORT 2 supports RS-232 and RS-485 communication only.

Содержание IFD9503


























































Результаты поиска

Содержание IFD9503

Отзывы:

Delta IFD9503, Руководство по применению, Страница: 9 / 57

Результаты поиска

Содержание IFD9503

Отзывы: