manualshive.com logo in svg

Delta IFD9503, Руководство по применению, Страница: 3 / 57

Поделиться
Скачать
Delta IFD9503 Скачать руководство пользователя страница 3

CANopen Slave Communication Module IFD9503

 

DVP-PLC Application Manual

 

1

 

Warning 

3

 Please read this instruction carefully before use and follow this instruction to operate the device in order to prevent 

damages on the device or injuries to staff.   

3

 Switch off the power before wiring. 

3

 IFD9503 is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, 

electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. 

key or specific tools are required for operating the enclosure) in case danger and damage on the device may occur. 

3

 IFD9503 is to be used for controlling the operating machine and equipment. In order not to damage it, only 

qualified professional staff familiar with the structure and operation of IFD9503 can install, operate, wire and 

maintain it.   

3

 DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check 

all the wirings again before switching on the power and DO NOT touch any terminal when the power is switched 

on. Make sure the ground terminal 

  is correctly grounded in order to prevent electromagnetic interference. 

 

 

 

Table of Contents

 

1

 

INTRODUCTION...................................................................................................................................3

 

1.1

 

IFD9503 Brief ............................................................................................................................3

 

1.2

 

Features ....................................................................................................................................3

 

2

 

COMPONENTS ....................................................................................................................................5

 

2.1

 

Product Profile and Outline .......................................................................................................5

 

2.2

 

CANopen Connector .................................................................................................................5

 

2.3

 

Address Setup Rotary Switch....................................................................................................5

 

2.4

 

Function Setup DIP switch ........................................................................................................6

 

2.5

 

Communication Ports on IFD9503 ............................................................................................7

 

3

 

FUNCTIONS OF IFD9503 ....................................................................................................................8

 

3.1

 

Common Functions ...................................................................................................................8

 

3.2

 

When IFD9503 is connected to AC motor drive ......................................................................12

 

3.3

 

When IFD9503 is connected to temperature controller (DTA/DTB) ........................................15

 

3.4

 

When IFD9503 is connected to ASD-A servo drive.................................................................19

 

3.5

 

When IFD9503 is connected to programmable logic controller...............................................22

 

3.6

 

When IFD9503 is connected to Delta DOP-A HMI ..................................................................26

 

3.7

 

When IFD9503 is connected to custom equipment.................................................................31

 

4

 

LED INDICATORS & TROUBLE-SHOOTING....................................................................................35

 

4.1

 

RUN LED.................................................................................................................................35

 

4.2

 

ERROR LED ...........................................................................................................................35

 

4.3

 

SCAN LED ..............................................................................................................................35

 

Содержание IFD9503


























































Отзывы:

Нет отзывов