background image

-      - 

KEYBOARD

 

AND

 

MENU

 

DESCRIPTION 

 
Foreword 

The  instrument  keyboard  is  composed  of  single-function  keys,  like  the  UNIT  key,  and  double-
function keys such as the ON-OFF/Auto-OFF key.  
In the double-keys, the function in the upper part is the “main function”, while the one in the bottom 
part is the “secondary function”. When the instrument is in standard measurement mode, the main 
function  is  active.  In  the  menu  or  in  conjunction  with  the  FUNC  key,  the  secondary  function  is 
enabled.  
The  pressing  of  a  key  is  accompanied  by  a  short  confirmation  beep:  a  longer  beep  sounds  if  the 
wrong key is pressed. 
 

Note:

  the  instrument  is  fitted  with  internal  pressure  sensor  with  a  fixed  full  scale. 

If  a  SICRAM 

PP471  module  with  TP704  or  TP705  probe  is  connected,  the  internal  sensor  is  disabled  and 
the display indicated pressure is that of the external probe.

  

 

All operations described below and relevant to pressure measurement, therefore apply to the 
internal  sensor  unless  the  external  PP471  module  is  connected

.  Please  see  the  paragraph 

dedicated to calibration on page 14. 
 
Each key specific function is described in detail below. 
 
 

 

ON-OFF/Auto-OFF key

 

 
The  instrument  is  turned  on  and  off  using  the  ON/OFF  key.  The  turning  on  enables  all  display 
segments  for  a  few  seconds,  starts  an  auto-test  including  the  detection  of  the  possible  probe 
connected to the input, and sets the instrument ready for normal measurement. During the auto-test, 
the  serial  number  of  the  connected  probe  is  indicated  in  the  comment  line:  e.g. 
"PRB1_SER_1234_5678" means the probe with serial number 12345678 is connected to the input.  

 

 

 

If no probe is connected to central input, the "NO_PRBE_ SER_NUM" message appears for 
a few seconds in the line for symbols. 

 

When  the  probe  is  inserted  into  a  functioning  instrument,  the  "NEW_PROB_DET"  (New 
probe  detected)  message  appears:  as  the  probe's  data  are  captured  upon  turning  the 
instrument on, it is necessary to turn the instrument off and on again. 

 

Replace the probes when the instrument is off. 

 
 

MIN

cm

min

s

2

3

m

µ

m

k

>>>

Содержание HD2114.0









































Отзывы: