Delta HD2114.0 Скачать руководство пользователя страница 35

Страница: 35 / 40

- -

RESSURE MEASUREMENT PROBES

PP471

SICRAM interface module between instrument and TP704 and TP705 series
Delta Ohm probes. Cable length 2 metres.

The list of pressure probes is outlined in the table on page 31.

EMPERATURE PROBES COMPLETE WITH

SICRAM

MODULE

TP472I

Immersion probe, sensor Pt100. Stem Ø 3 mm, length 300 mm. Cable length 2
metres.

TP472I.0

Immersion probe, sensor Pt100. Stem Ø 3 mm, length 230 mm. Cable length 2
metres.

TP473P.I

Penetration probe, sensor Pt100. Stem Ø 4mm, length 150 mm. Cable length 2
metres.

TP473P.0

Penetration probe, sensor Pt100. Stem Ø 4mm, length 150 mm. Cable length 2
metres.

TP474C.I

Contact probe, sensor Pt100. Stem Ø 4 mm, length 230 mm, contact surface Ø
5mm. Cable length 2 metres.

TP474C.0

Contact probe, sensor Pt100. Stem Ø 4 mm, length 230 mm, contact surface Ø
5 mm. Cable length 2 metres.

TP475A.0

Air probe, sensor Pt100. Stem Ø 4 mm, length 230 mm. Cable length 2 metres.

TP472I.5

Immersion probe, sensor Pt100. Stem Ø 6 mm, length 500 mm. Cable length 2
metres.

TP472I.10

Immersion probe, sensor Pt100. Stem Ø 6 mm, length 1000 mm. Cable length 2
metres.

TP49A.O

Immersion probe, sensor Pt100. Stem Ø 2.7 mm, length 150 mm. Cable length 2
metres. Aluminium handle.

TP49AC.O

Contact probe, sensor Pt100. Stem Ø 4 mm, length 150 mm. Cable length 2
metres. Aluminium handle.

TP49AP.O

Penetration probe, sensor Pt100. Stem Ø 2.7 mm, length 150 mm. Cable length 2
metres. Aluminium handle.

TP875.I

Globe-thermometer Ø 150 mm with handle. Cable length 2 metres.

TP876.I

Globe-thermometer Ø 50 mm with handle. Cable length 2 metres.

TP87.O

Immersion probe, sensor Pt100. Stem Ø 3 mm, length 70 mm. Cable length 2
metres.

TP878.O

Contact probe for solar panels. Cable length 2 metres.

TP878.1.O

Contact probe for solar panels. Cable length 5 metres.

TP879.O

Penetration probe for compost. Stem Ø 8 mm, length 1 metre. Cable length 2
metres.

Содержание HD2114.0









































Результаты поиска

Содержание HD2114.0

Отзывы:

Похожие инструкции для HD2114.0

Бренды по названию

Популярные бренды

Delta HD2114.0, Руководство пользователя

Результаты поиска

Содержание HD2114.0

Отзывы:

Похожие инструкции для HD2114.0

Бренды по названию

Популярные бренды