Delta HD2114.0 Скачать руководство пользователя страница 36

Страница: 36 / 40

- -

EMPERATURE PROBES WITHOUT

SICRAM

MODULE

TP47.100.O

Immersion probe, sensor Pt100 direct 4 wires. Probe's stem Ø 3mm, length
230mm. 4-wire connection cable with connector, length 2 metres.

TP47.1000.O

Immersion probe, sensor Pt1000. Probe's stem Ø 3mm, length 230mm. 2-wire
connection cable with connector, length 2 metres.

TP87.100.O

Immersion probe, sensor Pt100 direct 4 wires. Probe's stem Ø 3mm, length 70mm.
4-wire connection cable with connector, length 2 metres.

TP87.1000.O

Immersion probe, sensor Pt1000. Probe's stem Ø 3mm, length 70mm. 2-wire
connection cable with connector, length 2 metres.

TP47

Only connector for probe connection: Pt100 direct 3 and 4 wires, Pt1000 and
Ni1000 2 wires.

DELTA OHM metrology laboratories LAT N° 124 are accredited by ACCREDIA for Temperature,
Humidity, Pressure, Photometry / Radiometry, Acoustics and Air Velocity. They can supply
calibration certificates for the accredited quantities.

Содержание HD2114.0









































Результаты поиска

Содержание HD2114.0

Отзывы:

Похожие инструкции для HD2114.0

Бренды по названию

Популярные бренды

Delta HD2114.0, Руководство пользователя

Результаты поиска

Содержание HD2114.0

Отзывы:

Похожие инструкции для HD2114.0

Бренды по названию

Популярные бренды