Delta HD2114.0 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 40

background image

- -

28

NOTES ABOUT WORKING AND OPERATIVE SAFETY

Authorized use

The technical specifications as given in chapter "TECHNICAL CHARACTERISTICS" must be
observed. Only the operation and running of the measuring instrument according to the instructions
given in this operating manual is authorized. Any other use is considered unauthorized.

General safety instructions

This  measuring  system  is  constructed  and  tested  in  compliance  with  the  EN  61010-1  safety
regulations  for  electronic  measuring  instruments.  It  left  the  factory  in  a  safe  and  secure  technical
condition.
The smooth functioning and operational safety of the measuring system can only be guaranteed if
the  generally  applicable  safety  measures  and  the  specific  safety  instructions  in  this  operating
manual are followed during operation.
The smooth functioning and operational safety of the instrument can only be guaranteed under the
environmental  and  electrical  operating  conditions  that  are  in  specified  in  chapter  "TECHNICAL
CHARACTERISTICS".

Do not use or store the product in places such as listed below:

Rapid changes in ambient temperature which may cause condensation.

Corrosive or inflammable gases.

Direct vibration or shock to the instrument.

Excessive induction noise, static electricity, magnetic fields or noise.

If  the  measuring  system  was  transported  from  a  cold  environment  to  a  warm  environment,  the
formation  of  condensate  can  impair  the  functioning  of  the  measuring  system.  In  this  event,  wait
until  the  temperature  of  the  measuring  system  reaches  room  temperature  before  putting  the
measuring system back into operation.

Obligations of the purchaser

The purchaser of this measuring system must ensure that the following laws and guidelines are
observed when using dangerous substances:



EEC directives for protective labour legislation



National protective labour legislation



Safety regulations

«
...
26
27
28
29
30
...
»

Содержание HD2114.0









































Отзывы:

Нет отзывов

Похожие инструкции для HD2114.0

Бренд: Galileo Страницы: 19

Бренд: Galileo Страницы: 71

Бренд: Waltron Страницы: 11

Бренд: Labom Страницы: 6

Бренд: Labom Страницы: 5

Бренд: Kathrein Страницы: 10

Бренд: Omano Страницы: 14

Бренд: QuantAsylum Страницы: 70

Бренд: Hanna Instruments Страницы: 9

Бренд: Leica Страницы: 2

DIGIMET E30 Preset

Бренд: MATO Страницы: 20

Бренд: Kawai Страницы: 72

Бренд: OmegaWatt Страницы: 9

Engine Analyzer Series

Бренд: ACCEL DFI Страницы: 39

FlowStar2 LB 514

Бренд: BERTHOLD TECHNOLOGIES Страницы: 130

Бренд: Megger Страницы: 8

Бренд: TESTO Страницы: 2

COOL-US CU-935A

Бренд: Y?lmaz So?utma Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды