Delta Water Engineering Escalda Скачать руководство пользователя страница 3

P0522 

         DELTA WATER ENGINEERING 

V01/2017/P3

 

2.

 

Precautions: 

 

2.1

 

General: 
 

 

Make sure you have the latest installation manual at hand. Check with your 
Delta supplier. 

 

Read this manual carefully. If you have any questions or remarks, please 

contact your Delta supplier. 

 

Make sure you have all necessary tools on hand before you begin with the 

installation. 

 

Follow all local legal regulations. 

 

2.2

 

Water to be treated: 
 

 

Check  incoming  pressure:  minimum  1  bar  (dynamic),  maximum  8  bar 
(static) (15 PSI- 116 PSI). If necessary reduce incoming pressure. 

 

The  pressure  behind  the  softener  must  be  at  least  1bar  to  ensure  a  good 

functioning  of  the  softener.  If  this  pressure  of  at  least  1bar  can’t  be 
guaranteed, a “Pressure Guard” is available at your Delta supplier. 

 

The water should be free of sediment, chlorine, iron and manganese. 
 

2.3

 

Softener: 

 

 

The softener has to be installed on a flat, stable base. 

 

The softener must be installed indoors, protected from direct sunlight. 

 

The  softener  must  be  installed  on  a  dry  location  and  certainly  not  in  an 

acidic environment. 

 

Do  not  install  the  Delta  Softener  close  to  a  heating  source  (environment 
temperature must be below 40°C).  

 

Protect softener and drain (12) against frost. 

 

The Delta Bypass is not designed to be left behind without the softener. It is 

not a shutoff valve. 

 

The provided overflow has to be installed and connected at all times. 

 

 
 
 

 
 

 
 

 
 

 
 

 
 

 
 

 

Содержание Escalda

















Отзывы: