Delta OHM HD45 17A страница 64 Скачать руководство пользователя | Manualshive

Страница: 64 / 72

background image

- 64 -

Instrument storage conditions

Temperature: -25...+70°C.

•

Humidity: 10...90%RH non-condensing.

•

In storing the instrument, avoid areas where:

There is a high humidity level.
The instrument is exposed to direct sunlight.
The instrument is exposed to a high temperature source.

There are high vibration levels.
There is presence of vapour, salt and/or corrosive gas.

Cleaning

The instrument housing is in ABS plastic material: do not use solvents that are not
compatible with cleaning purposes.

Authorized use
Observe the technical specifications indicated in this chapter. Only the use and

operation of this instrument in accordance with the instructions given in this manual
are authorized. Any other use is to be considered as not authorized.

General safety instructions
This instrument has been manufactured and tested in accordance with EN61010-1
safety directives for electronic measuring instruments and has left the factory in

perfect safety technical conditions.
The instrument proper operation and operating safety can be ensured only if all
standard safety measures as well as the specific measures described in this manual

are followed.
The instrument proper operation and operating safety can be ensured only in the
climatic conditions specified in this manual.

Do not use the instrument in places where there are:

•

Rapid ambient temperature variations that may cause condensation.

•

Corrosive or flammable gases.

•

Direct vibrations or bumps to the instrument.

•

High-intensity electromagnetic fields, static electricity.

If the instrument is moved from a cold place to a hot one, or vice versa, condensation
formation can cause instrument malfunction. In this case, you will have to wait for the
instrument temperature to reach ambient temperature level before turning the

instrument on.

User obligations
The instrument operator shall follow the directives and regulations below that refer to
hazardous materials treatment :

EEC directives on workplace safety

National law regulations on workplace safety

Accident prevention regulations

«
...
62
63
64
65
66
...
»

Содержание HD45 17A









































































Отзывы:

Нет отзывов

Похожие инструкции для HD45 17A

ATR833A-II-OLED

Бренд: F.u.n.k.e. Страницы: 56

Бренд: Dataradio Страницы: 49

Бренд: Yaesu Страницы: 34

Бренд: Yaesu Страницы: 33

Бренд: Yaesu Страницы: 13

Бренд: Yaesu Страницы: 56

Бренд: Yaesu Страницы: 54

Бренд: Yaesu Страницы: 39

Бренд: Yaesu Страницы: 90

Бренд: Yaesu Страницы: 22

Бренд: Yaesu Страницы: 2

Бренд: Yaesu Страницы: 60

Бренд: Yaesu Страницы: 193

Бренд: Yaesu Страницы: 140

Бренд: Yaesu Страницы: 30

Бренд: ICS Страницы: 58

Бренд: RKI Instruments Страницы: 65

Бренд: Ten-Tec Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды