Delta OHM HD45 17A Скачать руководство пользователя страница 30

Страница: 30 / 72

- 30 -

Temperature analog output (°C)

DESCRIPTION

VALUE

DEFAULT NOTE

011 Minimum °C temperature that can

be associated to minimum scale
analog output (x10)

MIN: -300 (-30.0°C)

MAX: P#012

-300

(3)

012 °C temperature at minimum scale

analog output (x10)

MIN: P#011
MAX: P#013 – P#015

-200

(3)

013 °C temperature at 10V or 20mA

analog output (x10)

MIN: P#012 + P#015

MAX: P#014

800

(3)

014 Maximum °C temperature that can

be associated to 10V or 20mA

analog output (x10)

MIN: P#013

MAX: 850 (85.0°C)

850

(3)

015 Minimum °C temperature range for

analog output (x10)

MIN: 100 (10.0°C) 200

(3)

(3) The displayed value is the quantity value multiplied by 10 (decimal point not shown).

Temperature (°F) analog output

DESCRIPTION

VALUE

DEFAULT NOTE

016 Minimum °F temperature that can

be associated to minimum scale
analog output (x10)

MIN: -220 (-22.0°F)

MAX: P#017

-220

(3)

017 °F temperature at minimum scale

analog output (x10)

MIN: P#016
MAX: P#018 – P#020

-40

(3)

018 °F temperature at 10V or 20mA

analog output (x10)

MIN: P#017 + P#020
MAX: P#019

1760

(3)

019 Maximum °F temperature that can

be associated to 10V or 20mA

analog output (x10)

MIN: P#018
MAX: 1850 (185.0°F)

1850

(3)

020 Minimum °C temperature range for

analog output (x10)

MIN: 180 (18.0°F) 360

(3)

(3) The displayed value is the quantity value multiplied by 10 (decimal point not shown).

Humidity analog output (RH%)

DESCRIPTION

VALUE

DEFAULT NOTE

021 Minimum % relative humidity that

can be associated to minimum
scale analog output (x10)

MIN: 0 (0.0%)

MAX: P#022

(3)

022 % relative humidity at minimum

scale analog output (x10)

MIN: P#021

MAX: P#023 – P#025

(3)

023 % relative humidity at 10V or

20mA analog output (x10)

MIN: P#022 + P#025
MAX: P#024

1000

(3)

024 Maximum % relative humidity that

can be associated to 10V or 20mA

analog output (x10)

MIN: P#023
MAX: 1000 (100.0%)

1000

(3)

025 Minimum % relative humidity range

for analog output (x10)

MIN: 100 (10.0%) 200

(3)

(3) The displayed value is the quantity value multiplied by 10 (decimal point not shown).

Содержание HD45 17A









































































Результаты поиска

Содержание HD45 17A

Отзывы:

Delta OHM HD45 17A, Руководство пользователя, Страница: 30 / 72

Результаты поиска

Содержание HD45 17A

Отзывы: