Delta OHM HD45 17A Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 72

Delta OHM HD45 17A Скачать руководство пользователя страница 15

- 15 -

“CONFIGURATION”). Please note, however, that hysteresis and intervention mode
with the rotary selector in zero position differ from hysteresis and intervention mode
with the rotary selector in position other than zero.
If the relay is associated with temperature, the selector is preset as follows:

Tab. 4.D: Default settings for temperature selector

POSITION

TEMPERATURE RELAY THRESHOLD (°C)

0

Rotary selector disabled

1 18.0
2 23.0
3 28.0
4 33.0
5 38.0
6 43.0
7 48.0
8 53.0
9 58.0

Hysteresis is preset to 5.0°C and can be modified. Either threshold 1 value and the

interval between subsequent positions can be changed. For settings, see section
“CONFIGURATION”.

Relay outputs in HD46…R models
In HD46…R models as well, the relay can be used in two modes:

• Simplified mode: relays operate with a single, freely settable threshold; if the

instrument is supplied with a keyboard, it has a threshold
quick setting mode.

• Complete mode: relays can operate with one or two thresholds, the quick

setting mode is disabled.

The instrument is preset in complete mode with the following thresholds:

Tab. 4.E: Relay output default settings in HD46 models

(complete mode)

Temperature

Humidity

CO

2

Threshold = 20.0 °C

Threshold = 50.0 %

Threshold = 1000 ppm

Hysteresis = 5.0 °C

Hysteresis = 5.0 %

Hysteresis = 100 ppm

If the simplified mode is enabled, the preset thresholds will be as follows:

Tab. 4.F: Relay output default settings in HD46 models

(simplified mode)

Temperature

Humidity

CO

2

Threshold = 21.0 °C

Threshold = 50.0 %

Threshold = 800 ppm

Hysteresis = 5.0 °C

Hysteresis = 5.0 %

Hysteresis = 100 ppm

Please note that thresholds and relay operation modes in simplified mode differ from

thresholds and relay operation modes in complete mode, see section
“CONFIGURATION”.

«
...
13
14
15
16
17
...
»

Содержание HD45 17A









































































Отзывы:

Нет отзывов