Delta Electronics AC Motor Drive VFD007S23A Скачать руководство пользователя страница 130

Страница: 130 / 186

Chapter 5 Parameters

VFD-S Series

Revision August 2006, SE08, SW V2.61

5-75

Group A: PID Control

A-00

Input Terminal for PID Feedback

Factory Setting: d0

Settings

Disable

Negative PID feedback from external terminal (AVI) 0 to +10V

Negative PID feedback from external terminal (ACI) 4 to 20mA

Positive PID feedback from external terminal (AVI) 0 to +10V

Positive PID feedback from external terminal (ACI) 4 to 20mA

Select an input terminal to serve as the PID feedback location. Please verify the feedback

location is different from the Frequency Set Point location and J1 for selecting ACI or AVI

must be in the correct position. (Refer to Pr. 2-00 for detail)

Negative feedback = Positive target value – detection value.

Positive feedback = Negative target value + detection value.

A-01

Gain over PID Detection value

Settings

d0 to d999 (d100 means gain value is 1)

Factory Setting: d100

To adjust feedback detective gain value. It is used to adjust target value error.

A-02

Proportional Gain (P)

Unit: 1

Settings

d0 to d999% (d0: disable) (d100 means
gain value is 1)

Factory Setting: d100

This parameter is used to determinate error gain. If I = 0 and D = 0, doing proportional gain

operation.

A-03

Integral Time (I)

Unit: 1

Settings

d0 to d999

Factory Setting: d100

Disable

When this parameter is defined to gain is 1 and error value is fixed, integral value is equal to

error value as the setting of integral time is attained.

A-04

Derivative Control (D)

Unit: 1

Settings

d0 to d100

Factory Setting: d0

Disable

Содержание AC Motor Drive VFD007S23A



























































































































































































Результаты поиска

Содержание AC Motor Drive VFD007S23A

Отзывы:

Похожие инструкции для AC Motor Drive VFD007S23A

Бренды по названию

Популярные бренды

Delta Electronics AC Motor Drive VFD007S23A, Руководство пользователя

Результаты поиска

Содержание AC Motor Drive VFD007S23A

Отзывы:

Похожие инструкции для AC Motor Drive VFD007S23A

Бренды по названию

Популярные бренды