Dell XPS 8920 Скачать руководство пользователя страница 95

Страница: 95 / 102

NOTE:

For more information on the location of the CMOS jumper, see “

2. Remove the power cord.
3. Remove the jumper plug from the password jumper-pins (PSWD) and connect it to the CMOS jumper-pins.
4. Wait for 5 seconds and then replace the jumper plug to the password jumper-pins (PSWD).

Figure 45. Clearing the CMOS

a. jumper plug
b. CMOS jumper-pins
c. password jumper-pins (PSWD)

Post-requisites

1. Replace the

right side-cover

2. Follow the procedure from step 9 to step 10 in “

Replacing the power-supply unit

”.

Clearing forgotten passwords

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

System setup

Содержание XPS 8920







































































































Результаты поиска

Содержание XPS 8920

Отзывы:

Похожие инструкции для XPS 8920

Бренды по названию

Популярные бренды

Dell XPS 8920, Руководство по обслуживанию

Результаты поиска

Содержание XPS 8920

Отзывы:

Похожие инструкции для XPS 8920

Бренды по названию

Популярные бренды