Dell USC Скачать руководство пользователя страница 118

Страница: 118 / 132

118

Troubleshooting and Frequently Asked Questions

Frequently Asked Questions

When USC-LCE downloads updates, where are the files stored?

The files are stored in non-volatile memory, located on the main system

board. This memory is not removable and is not accessible through the

operating system.

Is a virtual media device or vFlash SD card required to store data for

updates?

No. The files are stored in memory on the main system board.

What is virtual media?

Virtual media is remote media—like CDs, DVDs, and USB keys—that a

server identifies as local media.

What should I do if an update fails?

If an update fails, USC-LCE will reboot and then attempt all the

remaining pending updates selected. After the final reboot, the system

returns to the USC-LCE

Home

page. Launch

Platform Updates

again and

then re-select the update that had failed and click

Apply

What is vFlash SD card?

vFlash SD card is a formatted SD (Secure Digital) card that plugs into

iDRAC6 Enterprise. vFlash SD card can be formatted and enabled via

iDRAC to make it accessible as a USB drive for data storage. Virtual flash is

a partition on vFlash SD card to which you can remotely write an ISO. See

the

Integrated Dell Remote Access Controller 6 (iDRAC6) User’s Guide

available at

support.dell.com/manuals

for more information.

Can I add my own drivers to use for operating system installation?

No. You cannot add your own drivers for operating system installation.

See

Updating Platform

for more information on updating the drivers that

are used for operating system installation.

Содержание USC





































































































































Результаты поиска

Содержание USC

Отзывы:

Бренды по названию

Популярные бренды

Dell USC, Руководство пользователя

Результаты поиска

Содержание USC

Отзывы:

Бренды по названию

Популярные бренды