Dell S5448F-ON Скачать руководство пользователя страница 3

Страница: 3 / 56

Chapter 1: About this guide........................................................................................................... 5

Chapter 2: The S5448F-ON switch................................................................................................ 7

Introduction........................................................................................................................................................................... 7

20W optic port locations..............................................................................................................................................8

LED behavior...................................................................................................................................................................9

Chapter 3: Site preparations........................................................................................................ 13

Chapter 4: S5448F-ON switch installation................................................................................... 16

Four-post L-bracket rail installation.........................................................................................................................17
Four-post ReadyRail installation............................................................................................................................... 21

Optics installation.............................................................................................................................................................. 27

Optics removal............................................................................................................................................................. 28

Chapter 5: Power supplies...........................................................................................................30

Chapter 6: Fans...........................................................................................................................35

Contents

Содержание S5448F-ON

























































Результаты поиска

Содержание S5448F-ON

Отзывы:

Похожие инструкции для S5448F-ON

Бренды по названию

Популярные бренды

Dell S5448F-ON, Руководство по установке

Результаты поиска

Содержание S5448F-ON

Отзывы:

Похожие инструкции для S5448F-ON

Бренды по названию

Популярные бренды