Dell S5448F-ON Скачать руководство пользователя страница 9

Страница: 9 / 56

●

One USB Type-A port for more file storage

●

One MicroUSB Type-B console port for management

●

Intel Denverton C3758 eight-core central processing unit (CPU), 2.2 GHz, 32 GB DDR4 ECC

●

One 10/100/1000BaseT Ethernet management port

●

Temperature monitoring

●

Software-readable thermal monitor

●

Real-time clock (RTC) support

●

Two hot-pluggable redundant PSUs

●

Six hot-pluggable replaceable fan modules

●

Power management monitoring

Physical dimensions

The S5448F-ON switch have the following physical dimensions:

●

438.5 x 550 x 43 mm (W x D x H)

●

17.26 x 21.65 x 1.693 inches (W x D x H)

●

PSU handle 29.3 mm (1.15 in)

●

PSU latch 34.6 mm (1.37 in)

●

Fan tray handle 25.0 mm (0.99 in)

LED display

The S5448F-ON switch includes LED displays on the I/O side of the switch. This section describes open networking installation
environment (ONIE) LED behaviors. Some LED behaviors may change after you install your software.

LED behavior

The following S5448F-ON switch LED behavior is seen during startup:

1. Locator LED

2. System LED

3. Power LED

4. Fan LED

5. Port activity LED

6. Port activity LED

7. Top: RJ-45 Ethernet Management Port LED. Bottom: RJ-45

Serial Console Port (no LED). Left is link; right is activity.

8. Port activity LED

Table 1. S5448F-ON switch LED behavior

LED

Description

System Health Status LED

●

Solid green—Normal operation

The S5448F-ON switch

Содержание S5448F-ON

























































Результаты поиска

Содержание S5448F-ON

Отзывы:

Похожие инструкции для S5448F-ON

Бренды по названию

Популярные бренды

Dell S5448F-ON, Руководство по установке

Результаты поиска

Содержание S5448F-ON

Отзывы:

Похожие инструкции для S5448F-ON

Бренды по названию

Популярные бренды