Dell PowerVault MD3800i Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 56

background image

The default IP configuration for Controller 1 is:

Port 0:192.168.129.102

NOTE: No default gateway is set.

NOTE: If DHCP is not used, perform the initial configuration using the management station on the
same physical subnet as the storage array. Additionally, during initial configuration, configure at
least one network adapter on the same IP subnet as the storage array’s default management port.
After initial configuration (management ports are configured using MD Storage Manager), you can
change the management station’s IP address back to its previous settings.

Default Management IPv6 Port Settings

By default, the storage array management ports are enabled for IPv6 stateless auto-configuration. The
ports are automatically configured to respond to their link local address and to a routable address if a
configured IPv6 router is present on the network.

Locating The Link Local Addresses Of The Management Port

To locate the link local address on the management port, see the MAC label for the management port on

the controller.

NOTE: This procedure applies to out-of-band management only. If you choose to set up in-band
management, you must complete this step and then proceed to "Step 8: (Optional) Set Up In-Band

Management".

1.

If the MAC Address is 00:08:74:AA:BB:CC, the link local address starts with FE80::02.

2.

Add the second and third bytes 08:74 MAC address to the prefix FE80::0208:744.

3.

Add FF:FE to obtain FE80::0200:08FF:FE.

4.

Finally, add the last 3 bytes of the MAC address FE80::0200:08FF:FEAA:BBCC.

Figure 15. Management Port MAC Address

NOTE: This procedure applies to out-of-band management only. If you choose to set up in-
band management, you must complete this step and then proceed to

Setting Up In-Band

Management

.

You can discover the storage array either automatically or manually. Select one and complete the
following procedure.

40

«
...
38
39
40
41
42
...
»

Содержание PowerVault MD3800i

























































Отзывы:

Нет отзывов

Похожие инструкции для PowerVault MD3800i

XCubeNAS XN7012R

Бренд: Qsan Страницы: 16

Бренд: QNAP Страницы: 39

Бренд: Apricorn Страницы: 4

Бренд: Nexsan Страницы: 76

Бренд: eazished Страницы: 12

Бренд: Quantum Страницы: 20

Mobileraid MR8X

Бренд: Sans Digital Страницы: 81

Бренд: kioxia Страницы: 24

CANOPIA RUBICON

Бренд: Palram Страницы: 71

PowerProtect X400

Бренд: Dell EMC Страницы: 42

Бренд: Clickfree Страницы: 76

DKC-F810I-1PL16

Бренд: Hitachi Страницы: 36

Бренд: Clarke Страницы: 12

Бренд: Kimberley Страницы: 2

MONACO-MKII KRB60EP

Бренд: Kimberley Страницы: 4

CHEETAH 9 ST19101DC

Бренд: Seagate Страницы: 56

Cheetah 9LP Series

Бренд: Seagate Страницы: 86

Бренд: Check Point Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды