Dell PowerConnect B-TI24x Скачать руководство пользователя страница 57

Страница: 57 / 82

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Replacing the fan tray

2. Loosen the two captive screws on the front plate of the fan tray and slide the tray out of the

device as shown in

Figure 23

FIGURE 23

Removing the fan tray

3. Insert the replacement fan tray, as shown in

Figure 24

, and push it all the way into the slot to

connect the interface.

NOTE

Ensure that the fan tray fits between the locating slides in the device.

4. Tighten the two captive screws to secure the tray in place.

FIGURE 24

Inserting a replacement fan tray

5. Connect the PDU power cords (C13-C14) to the power supply (refer to

“Powering on the

system”

on page 18).

6. Verify that the system is working properly as instructed in

“Verifying proper operation”

page 19.

Locating Slide

Содержание PowerConnect B-TI24x



















































































Результаты поиска

Содержание PowerConnect B-TI24x

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect B-TI24x, Руководство по установке оборудования

Результаты поиска

Содержание PowerConnect B-TI24x

Отзывы:

Бренды по названию

Популярные бренды