Dell PowerConnect B-TI24x Скачать руководство пользователя страница 55

Страница: 55 / 82

Dell PowerConnect B-Series TI24X Hardware Installation Guide

53-1002265-01

Replacing the fan tray

4. Lock the power supply in place by securing the two captive screws as shown in

Figure 20

FIGURE 20

Securing the power supply in the device

5. Connect the PDU power cords (C13-C14) to the power supply.

FIGURE 21

Connecting the PDU power cords (C13-C14)

6. Power on the supply and verify that it is working properly as instructed in

“Powering on the

system”

on page 18 and

“Verifying proper operation”

on page 19.

Replacing the fan tray

NOTE

You can replace the fan tray while the PowerConnect B-Series TI24X device is powered on and
running. But, you need to replace the fan tray quickly after removing it from the device, otherwise
the device will overheat.

The fan tray is located in a slot at the rear of the PowerConnect B-Series TI24X .

This section provides information about the following topics:

Содержание PowerConnect B-TI24x



















































































Результаты поиска

Содержание PowerConnect B-TI24x

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect B-TI24x, Руководство по установке оборудования

Результаты поиска

Содержание PowerConnect B-TI24x

Отзывы:

Бренды по названию

Популярные бренды