manualshive.com logo in svg

Dell PowerConnect B-TI24x, Руководство по установке оборудования

Поделиться
Скачать
Dell PowerConnect B-TI24x Скачать руководство пользователя страница 35

Dell PowerConnect B-Series TI24X Hardware Installation Guide

25

53-1002265-01

Configuring IP addresses

3

Configuring IP addresses

You must configure at least one IP address using the serial connection to the CLI before you can 
manage the system using the other management interfaces. In addition, 

Dell

 routers require an IP 

subnet address for the subnet in which you plan to place them in your network.

Dell PowerConnect devices support both classical IP network masks (Class A, B, and C subnet 
masks, and so on) and Classless Interdomain Routing (CIDR) and network prefix masks as follows:

•

To enter a classical network mask, enter the mask in IP address format. For example, enter,
"209.157.22.99 255.255.255.0" for an IP address with a Class-C subnet mask.

•

To enter a prefix number for a network mask, enter a forward slash ( / ) and the number of bits 
in the mask immediately after the IP address. For example, enter,
"209.157.22.99/24" for an IP address that has a network mask with 24 significant ("mask") 
bits.

By default, the CLI displays network masks in classical IP address format (example: 
255.255.255.0). You can change the display to the prefix format. Referto the 

PowerConnect 

B-Series TI24X Configuration Guide

.

Devices running Layer 2 software

Follow the steps to configure an IP address on a device running Layer 2 software.

1. At the opening CLI prompt, enter enable.

PowerConnect> enable

2. Enter the following command at the Privileged EXEC level prompt (for example, PowerConnect 

Switch#), then press Enter. This command erases the factory test configuration if still present.

PowerConnect# erase startup-config

CAUTION

Use the erase startup-config command only for new systems. If you enter this command on a 
system you have already configured, the command erases the configuration. If you accidentally 
do erase the configuration on a configured system, enter the write memory command to save the 
running configuration to the startup-config file.

3. Access the configuration level of the CLI by entering the following command.

PowerConnect# configure terminal Privileged EXEC Level

PowerConnect(config)# Global CONFIG Level

4. Configure the IP address and mask for the switch.

PowerConnect(config)# ip address 192.22.3.44 255.255.255.0

5. Set a default gateway address for the switch.

PowerConnect(config)# ip default-gateway 192.22.3.1

NOTE

You do not need to assign a default gateway address for single subnet networks.

Syntax: enable [<password>]

Содержание PowerConnect B-TI24x



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды