manualshive.com logo in svg

Dell PowerConnect B-TI24x, Руководство по установке оборудования

Поделиться
Скачать
Dell PowerConnect B-TI24x Скачать руководство пользователя страница 25

Dell PowerConnect B-Series TI24X Hardware Installation Guide

15

53-1002265-01

Preparing the installation site

2

Preparing the installation site

Cabling infrastructure

Ensure that the proper cabling is installed in the site. Refer to 

“Device specifications”

 on page 50 

for a summary of supported cabling types and their specifications.

Installation location

Before installing the device, plan its location and orientation relative to other devices and 
equipment. Allow at least 3 inches of space at the front of the device for the twisted-pair, 
fiber-optic, and power cabling to ensure there is no airflow blockage or interference of cable 
routing. Also, allow a minimum of 3 inches of space between the sides and the back of the device 
and walls or other obstructions. 

Installing the device

You can install  Dell PowerConnect devices on a desktop or in an equipment rack.

DANGER

Make sure the rack or cabinet housing the device is adequately secured to prevent it from 
becoming unstable or falling over.

DANGER

Mount devices in a rack or cabinet as low as possible. Place the heaviest device at the bottom 
and progressively lighter devices above.

Desktop installation

Follow the steps for desktop installation.

1. Set the device on a flat desktop, table, or shelf. Make sure that adequate ventilation is 

provided for the system. A 3 in. clearance is recommended on each side.

2. Proceed to 

“Powering on the system”

 on page 18.

Rack mount installation

For rack mount installation,the Dell PowerConnect B-Series TI24X supports the use of a two post 
Telco equipment rack and four post equipment rack. 

NOTE

For additional support under the stack of switches. Use Dell 1U shelf, Dell p/n:G118R.

Содержание PowerConnect B-TI24x



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды