20
|
Installing RPMs and Line Cards
www.dell.com | support.dell.com
Line Cards
Line cards are hot-swappable. Any line card can be inserted into any line card slot. Line card slots are
labeled 0 to 7; these labels can be seen when the fan tray is installed. Do not force line cards into the RPM
slot.
Line card LEDs are described in the documentation specific to each line card. Refer to the installation
documentation that came with the card for to understand LED appearance and meaning.
Blank Panels
Blanks are required in empty slots to control airflow for adequate system cooling, personal safety, and
EMI containment during operation.
The blank panels do not have board components or connector pins. Align the blank with the guides and
gently slide toward the backplane.
NOTE:
All chassis slots must be installed with operational modules or blanks. Always replace cards and blank
panels immediately.
Installing the RPMs and Line Cards
WARNING:
Electrostatic discharge (ESD) damage can occur when components are mishandled. Always
wear an ESD-preventive wrist or foot-heel ground strap when handling RPMs or line cards. Place RPMs and
line cards on an antistatic surface when they are not installed.
NOTE:
Unlock the levers before inserting the line card into to chassis. Fully engage the locking mechanism
once the card has been inserted; not doing so will cause damage to the card below when that card is inserted.
Flash
Slot
Use the compact flash card (external compact flash memory card) slot to store and retrieve
boot and system images.
In Use LED
Green: flash memory card is in the process of a read or write process. Do not remove the
flash card when the In Use LED is lit.
Unlit: not in use.
Master LED
Indicates that this RPM is the Primary RPM.
Green: primary
Unlit: secondary/ fatal error/ booting
Reset Button
Use this recessed reset switch to reset the RPM by inserting a small object, such as a pen tip,
to depress the button.
SFM Active
Green: Switch Fabric is active
Unlit: Switch Fabric is inactive
Status LED
Green: operational
Red: card problem state
Flashing green: booting/ diagnostics
Unlit: in standby mode or is off
Table 5-1. RPM Front Panel and LED Descriptions (continued)
Section
Label
Description
Содержание C300
