Dell Alienware m17 Скачать руководство пользователя страница 72

Страница: 72 / 119

Removing the display bezel

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Prerequisites

1. Remove the

base cover

2. Remove the

wireless card

3. Remove the

display assembly

Procedure

NOTE:

Ensure that the display assembly is placed on a clean and flat surface.

1. Using a plastic scribe, unhook and release the sides of the display bezel from the display assembly as shown in the image in

the following order: Top (camera)->Left->Right->Bottom (Alienware logo).

NOTE:

Note the location of each adhesive tape securing the display bezel to the display assembly (as shown in yellow).

2. Lift the display bezel off the display assembly.

Removing the display bezel

Содержание Alienware m17
























































































































Результаты поиска

Содержание Alienware m17

Отзывы:

Бренды по названию

Популярные бренды

Dell Alienware m17, Руководство по обслуживанию

Результаты поиска

Содержание Alienware m17

Отзывы:

Бренды по названию

Популярные бренды