Dell Alienware m17 Скачать руководство пользователя

Страница: 15 / 119

Screw list

NOTE:

When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and

then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is
restored when the component is replaced.

NOTE:

Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when

replacing a component.

NOTE:

Screw color may vary with the configuration ordered.

Table 1. Screw list

Component

Secured to

Screw type

Quantity

Screw image

Base cover

Palm-rest assembly

M2.5x9

Battery (Half-length)

Palm-rest assembly

M2x5

Battery (Full-length)

Palm-rest assembly

M2x5

Hard-drive assembly

Palm-rest assembly

M2x5

Fans

Heat sink

M2x3

Heat-sink assembly

System board and fan

M2x3

Wireless-card bracket

System board

M2x3

Solid-state drive bracket Palm-rest assembly

M2x3

Solid-state drive

Solid-state drive bracket

M2x2

I/O board

Palm-rest assembly

M2x5

Touchpad

Palm-rest assembly

M2x2.5

Display hinges

Palm-rest assembly

M2.5x4.5

Display hinges

Display back-cover and
antenna assembly

M2.5x4.5

Display panel

Display back-cover and
antenna assembly

M2x3

Screw list

Содержание Alienware m17
























































































































Результаты поиска

Содержание Alienware m17

Отзывы:

Похожие инструкции для Alienware m17

Бренды по названию

Популярные бренды

Dell Alienware m17, Руководство по обслуживанию

Результаты поиска

Содержание Alienware m17

Отзывы:

Похожие инструкции для Alienware m17

Бренды по названию

Популярные бренды