Dell Alienware m17 Скачать руководство пользователя | Manualshive

Страница: 42 / 119

background image

Procedure to remove M.2 2280 card

NOTE:

This procedure applies only to systems shipped with a M.2 2280 card installed.

NOTE:

Depending on the configuration ordered the system may have up to two M.2 cards installed. Supported card

configurations per M.2 card slot:

●

M.2 2230 solid-state drive + 2230 card bracket

●

M.2 2280 solid-state drive

●

M.2 2280 Intel Optane

NOTE:

For solid-state drives above 512 GB or Intel Optane above 118 GB a thermal shield is required for optimal heat

dissipation and is installed in the computer when these configurations are ordered. If these configurations are installed After
Point-of-Sale (APOS), contact Dell support for the thermal shield.

NOTE:

Depending on the number of M.2 cards installed at Point-of-Sale, the thermal shield installed in the computer may

be a full shield or a half shield. If two M.2 cards are installed After Point-of-Sale (APOS) contact Dell support for the full
thermal shield.

1. Remove the two screws (M2x3) that secure the M.2 thermal shield to the palm-rest assembly and system board.
2. Lift the M.2 thermal shield from the palm-rest assembly and system board

3. Remove the screw (M2x2) that secures the M.2 2280 card to the palm-rest assembly.
4. Slide and remove the M.2 2280 card from the M.2 card slot on the system board.

42

Removing the solid-state drive/Intel Optane

«
...
40
41
42
43
44
...
»

Содержание Alienware m17
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Alienware m17

VisionBook N15G Plus

Бренд: UMAX Technologies Страницы: 44

Бренд: Acer Страницы: 77

Бренд: IBM Страницы: 8

Бренд: Gigabyte Страницы: 125

Toughbook CF-72TCJUZPM

Бренд: Panasonic Страницы: 36

Бренд: AEG Страницы: 52

Бренд: Toshiba Страницы: 258

Бренд: Dell Страницы: 81

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

PCG-Z505R - VAIO - PII 366 MHz

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

PCG-Z505JE - VAIO - PIII 500 MHz

Бренд: Sony Страницы: 1

PCG-Z1WAP VAIO User Guide (primary manual)

Бренд: Sony Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды