background image

Removing the heat sink

NOTE:

 Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in 

Before working inside your computer

. After working inside your computer, follow the instructions in 

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

NOTE:

 The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

CAUTION:

 For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils

in your skin can reduce the heat transfer capability of the thermal grease.

Prerequisites

Remove the 

base cover

.

Procedure

1. Disconnect the left fan cable from the system board.
2. Disconnect the right fan cable from the system board.
3. Remove the four screws (M2x3) that secure the heat-sink assembly to the palm-rest assembly.
4. In the reverse sequential order (7>6>5>4>3>2>1), loosen the seven captive screws that secure the heat-sink assembly to

the system board.

5. Lift the heat-sink assembly off the system board.

24

Removing the heat sink

51

Содержание Alienware m17
























































































































Отзывы: