manualshive.com logo in svg

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 77 / 209

Поделиться
Скачать
Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 77

Steps

1. Press the blue release tabs to disengage the drive backplane from the hooks on the system.
2. Lift and pull the drive backplane out of the system.

NOTE:

 To avoid damaging the backplane, ensure that you move the control panel cables from the cable routing clips

before removing the backplane.

Figure 51. Removing the drive backplane

Next steps

1.

Replace the drive backplane

.

Installing the drive backplane

Prerequisites

1. Follow the safety guidelines listed in the 

Safety instructions

 on page 46.

2. Follow the procedure listed in the 

Before working inside your system

 on page 47.

3.

Remove the backplane cover

.

4. If installed,

remove the air shroud

.

5.

Remove all the drives

.

6.

Remove the cooling fan cage assembly

.

NOTE:

 To avoid damaging the backplane, ensure to move the control panel cables from the cable routing clips before

removing the backplane.

NOTE:

 Route the cable properly when you replace it to prevent the cable from being pinched or crimped.

Steps

1. Use the guides on the system as guides to align the slots on the backplane.

Installing and removing system components

77

Содержание PowerEdge R7525


















































































































































































































Отзывы:

Нет отзывов