manualshive.com logo in svg

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 176 / 209

Поделиться
Скачать
Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 176

b. Twist the cable to 180 degrees to connect the MB_SL3 and MB_SL4 to the J_SL3 and J_SL4 connectors on the system board.
c. Install the cable tie and tighten to fix the cables.
d. To know the XGMI cable connectors on the system board, refer to the 

System board jumpers and connectors

 topic.

8.

Install the full length expansion card riser

 or 

half height expansion card riser

. See GPU kit components table for supported GPU risers.

9.

Install the GPU air shroud top cover

.

10. Install the foam on the system cover. To install the foam,

a. Place the system cover with the System Information Lable (SIL) side facing up.
b. For easier handling, peel off a small section of the adhesive cover and align the foam with the system cover.
c. Remove rest of the adhesive cover, and install foam on the system cover.
d. Press along the length of the foam to ensure that it is firmly affixed to the system cover.

Figure 132. Installing Mylar foam on the system cover

After installing, follow the 

after working inside the system

 instructions.

176

Upgrade Kits

Содержание PowerEdge R7525


















































































































































































































Отзывы:

Нет отзывов