manualshive.com logo in svg

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 164 / 209

Поделиться
Скачать
Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 164

Figure 124. Installing a power supply unit

Next steps

1. If you have unlatched or removed the cable management accessory, re-install or relatch it. For information about the cable

management when the PSU is removed or installed while the system is in the rack, see the system’s cable management accessory
documentation at 

https://www.dell.com/poweredgemanuals

.

2. Connect the power cable to the PSU, and plug the cable into a power outlet.

CAUTION:

 When connecting the power cable to the PSU, secure the cable to the PSU with the strap.

NOTE:

 When installing, hot swapping, or hot adding a new PSU, wait for 15 seconds for the system to recognize the

PSU and determine its status. The PSU redundancy may not occur until discovery is complete. The PSU status
indicator turns green to indicate that the PSU is functioning properly.

Trusted Platform Module

Upgrading the Trusted Platform Module

Prerequisites

NOTE:

• Ensure that your operating system supports the version of the TPM module being installed.
• Ensure that you download and install the latest BIOS firmware on your system.
• Ensure that the BIOS is configured to enable UEFI boot mode.

About this task

CAUTION:

 Once the TPM plug-in module is installed, it is cryptographically bound to that specific system board. Any

attempt to remove an installed TPM plug-in module breaks the cryptographic binding, the removed TPM cannot be
reinstalled or installed on another system board.

Removing the TPM

Steps

1. Locate the TPM connector on the system board.

164

Installing and removing system components

Содержание PowerEdge R7525


















































































































































































































Отзывы:

Нет отзывов