Deif SGC 120 Скачать руководство пользователя страница 45

Страница: 45 / 72

No.

Alarms

Causes/Indication

Actions

Low Fuel level (Sensor)

Indicates that the amount of fuel level is below the preset
threshold. This condition is detected only when engine is
on.

Shutdown
Warning

Low Fuel level (Switch)

Indicates that the amount of fuel level measured is low
through switch.

Shutdown
Warning
Electrical Trip
Notification

Low Water Level (Switch)

Indicates that radiator water level is below the preset
threshold.

Shutdown
Warning
Electrical Trip
Notification

Auxiliary input/User defined
name

Configured auxiliary input has triggered longer than preset
duration.

Shutdown
Warning
Electrical Trip
Notification

Anlg LOP Ckt Open

The oil pressure sensor is not detected (circuit open).

Shutdown
Warning
Electrical Trip
Notification

Engine Temp Ckt Open

The temperature sensor is not detected (circuit open).

Shutdown
Warning
Electrical Trip
Notification

Fuel Level Ckt Open

The fuel level sensor is not detected (circuit open).

Shutdown
Warning
Electrical Trip
Notification

Fuel Theft

The fuel consumption has exceeded the preset threshold.

Warning

Emergency Stop

Configured as digital input has triggered longer than preset
or when an immediate shutdown is required.

Shutdown

Fail To Stop

It is detected that genset is still running after sending stop
command.

Shutdown

Fail To Start

Indicates that genset has not started after the preset
number of start attempts.

Shutdown

L1 Phase Over Voltage

Indicates that genset (L1) phase voltage has exceeded the
preset over-voltage threshold.

Shutdown
Warning

L2 Phase Over Voltage

Indicates that genset (L2) phase voltage has exceeded the
preset over-voltage threshold.

Shutdown
Warning

L3 Phase Over Voltage

Indicates that genset (L3) phase voltage has exceeded the
preset over-voltage threshold.

Shutdown
Warning

L1 Phase Under Voltage

Indicates that genset (L1) phase voltage has fallen below
preset under-voltage threshold.

Shutdown
Warning

L2 Phase Under Voltage

Indicates that genset (L2) phase voltage has fallen below
preset under-voltage threshold.

Shutdown
Warning

L3 Phase Under Voltage

Indicates that genset (L3) phase voltage has fallen below
preset under-voltage threshold.

Shutdown
Warning

DG Phase Reversal

Alternator phase sequence (L1-L2-L3) is not correct.

Shutdown
Warning
Electrical Trip
Notification

USER MANUAL 4189341226A UK

Page 45 of 72

Содержание SGC 120









































































Результаты поиска

Содержание SGC 120

Отзывы:

Бренды по названию

Популярные бренды

Deif SGC 120, Руководство пользователя

Результаты поиска

Содержание SGC 120

Отзывы:

Бренды по названию

Популярные бренды