DEHACO IBEX 1200GS Скачать руководство пользователя страница 7

Страница: 7 / 40

1. Safety instructions

1.4 Protective equipment

Personal protective equipment must comply with

the applicable health and safety regulations.

Always wear the following personal protective

equipment:

◊ Protective helmet

◊ Safety glasses with side protectors

◊ Protective gloves

◊ Protective shoes

◊ Warning vest

1.5 Operation, precautions

WARNING!

If the load-bearing capacity of the carrier used is

insufficient, the carrier will not be stable. It can

topple over and cause injuries and damage.

Using a carrier whose load-bearing capacity is too

high will greatly burden the IBEX breaker causing

it to wear faster.

Only attach the IBEX breaker to a hydraulic

carrier of a suitable load-bearing capacity.

The carrier must remain stable at all times.

Read the carrier manufacturer’s Instructions

before attaching the IBEX breaker to the carrier

and operating it. Observe all instructions.

1.6 Hydraulic installation, precautions

WARNING!

If the hydraulic pressure is too high, the parts of

the IBEX breaker will be exposed to excessively

high loads. Parts can break loose or burst causing

serious injuries.

Connect the drain line of the pressure relief

valve directly in the tank to ensure the safe

functioning of the pressure relief valve!

The pressure relief valve must be set at the

maximum static pressure.

The pressure relief valve setting must be

checked to ensure that the maximum static

pressure (see chapter Technical specifications) of

the hydraulic installation is not exceeded at any

time. Attach a lead seal to the pressure relief

valve.

Prior to their first use, the safety facilities on

the hydraulic installation must be checked by

a professional/authorised monitoring body

for their quality (CE mark etc.), suitability and

proper functioning.

If any significant changes are made to the

hydraulic installation, a new acceptance

inspection is to be carried out in accordance with

the relevant national safety provisions.

WARNING!

The hydraulic system is under high pressure.

Hydraulic lines may spring a leak or burst.

Hydraulic oil under pressure can lead to serious

injury.

When attaching the IBEX breaker do not lay any

hydraulic lines through the carrier’s cab.

Only use hydraulic lines which comply with the

highest quality requirements.

1.7 Media/consumables, precautions

WARNING!

Hydraulic oil will spray out under high pressure if

there is a leakage. The jet of oil might penetrate

people’s skin and cause permanent damage. Hot

hydraulic oil can cause burns.

Never use your hands to find leaks.

Always keep your face away from a possible

leak.

If hydraulic oil has penetrated your skin consult

a doctor immediately.

WARNING!

Spilt hydraulic oil can make a floor slippery. If

people slip they can be injured. Hydraulic oil is

environmentally harmful and must not penetrate

the ground or enter the water table or water

supplies.

Make sure not to spill any hydraulic oil.

Immediately clean the floor if you have spilt

hydraulic oil.

Observe all safety and environmental protection

provisions when handling hydraulic oil.

WARNING!

Hydraulic oil and grease can cause rashes (or even

eczema) if they come into contact with the skin.

Avoid all skin contact with hydraulic oil and

grease.

Use a suitable skin protection product.

Always wear safety gloves when working with

hydraulic oil or grease.

Immediately clean any skin that has been

contaminated by oil or grease with water and

soap.

Содержание IBEX 1200GS









































Результаты поиска

Содержание IBEX 1200GS

Отзывы:

Похожие инструкции для IBEX 1200GS

Бренды по названию

Популярные бренды

DEHACO IBEX 1200GS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IBEX 1200GS

Отзывы:

Похожие инструкции для IBEX 1200GS

Бренды по названию

Популярные бренды