DEHACO IBEX 1200GS Скачать руководство пользователя страница 14

Страница: 14 / 40

Dehaco B.V. • Kruisbaak 25 • 2165 AJ Lisserbroek (NL) •

✆

+31 (0)252 - 41 79 50 •



[email protected] • www.dehaco.nl

4. Installation

4. INSTALLATION

4.1 Tool

4.1.1 Selection of tools

Dehaco can offer a selection of tools to suit each

application. The correct tool must be selected to

ensure the best possible results and the longest

lifetime.

Dehaco offers the next following tools:

◊ Blunt

◊ Chisel

◊ Cone

◊ Moil

◊ Asphalt

ATTENTION!

Use only official tools from Dehaco. If you do use

other types of chisels the warranty expires.

The chisel can be very hot, make sure that the

tool is cooled with regularity.

Use of imitation tools will expire the warranty

period.

4.1.2 Installation and removal of the tool

Installation

1) For IBEX types 130GS to 400GS remove the spring

pin and tool pin using the tool included.

2) For IBEX types 600GS to 4000GS loosen cover plate

bolts and remove the cover plate, tool pin buffers

and tool pins.

3) Ensure that the new tool and the inside of the

front head is clean.

4) Apply chisel grease to the contact surfaces of the

tool, tool pins and bushes.

5) Insert the tool into the front head.

6) Insert the tool pin/s.

7) For IBEX types 130GS to 400GS use a hammer to

replace the spring pin, ensuring that it completely

supports the tool pin.

8) For IBEX types 600GS to 4000GS replace tool pin

buffer and cover and fasten bolts.

Removal

1) If the breaker is still mounted onto the excavator

place the breaker horizontally on level ground.

Ensure that the excavator is turned off and

pressure from the hydraulic system released.

2) For IBEX types 130GS to 400GS remove the spring

pin and tool pin using the tool included.

3) For IBEX types 600GS to 4000GS loosen cover plate

bolts and remove the cover plate, tool pin buffers

and tool pins.

4) The tool should now be loose in the front head

and can be removed. Great care should be take

whilst doing this as a well lubricated chisel can

slide out by itself.

5) If the chisel is no longer suitable for operation

is should be cleaned and recycled in the proper

manner.

6) If no new tool is to be installed the tool pin

assembly should be reassembled.

4.2 Mounting the breaker on the

excavator

PLEASE NOTE

Make sure the breaker is mounted on an excavator

with sufficient capacity.

During installation, the excavator should only be

operated from the cabin.

Avoid contact with holes and mounting surfaces

when mounting the breaker.

Ensure that when the excavator is in motion,

nobody is in the swing radius.

Wear adequate personal protective equipment.

Procedure for pin and bush system

7) Place the breaker in a horizontal position on

beams on a flat surface.

8) Remove any mounted excavator attachments.

9) Insert pin and mount stop ring.

10) Adjust the speed of the engine to low idle.

11) Move the bucket cylinder, align the front linkage

holes with the mounting holes. Insert pin and

mount the stop ring.

12) Remove the cover of the valve and plugs from the

hoses. Connect hoses and valves.

13) Make sure the valves are in ‘on’ position.

For quick coupler or other systems, adhere to the

operation guidelines of the manufacturer.

Содержание IBEX 1200GS









































Результаты поиска

Содержание IBEX 1200GS

Отзывы:

Похожие инструкции для IBEX 1200GS

Бренды по названию

Популярные бренды

DEHACO IBEX 1200GS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IBEX 1200GS

Отзывы:

Похожие инструкции для IBEX 1200GS

Бренды по названию

Популярные бренды