DEHACO IBEX 1200GS Скачать руководство пользователя страница 6

Страница: 6 / 40

Dehaco B.V. • Kruisbaak 25 • 2165 AJ Lisserbroek (NL) •

✆

+31 (0)252 - 41 79 50 •



[email protected] • www.dehaco.nl

1. Safety instructions

1. SAFETY INSTRUCTIONS

Read these Safety and operating instructions and

specifically all safety instructions before using the

IBEX breaker. This will:

◊ prevent the risk of injuries and fatal accidents for

yourself and others,

◊ protect the IBEX breaker and other property

against material damage,protect the environment

against environmental damage.

Follow all instructions in this operation and

maintenance manual. Store this manual in de

document compartment of the carrier cab.

Anyone responsible for transporting, installing or

removing, operating, maintaining, repairing, storing

or disposing of the IBEX breaker must have read and

understood these Safety and operating instructions.

This operation and maintenance manual belongs to

the IBEX breaker. Keep it for the life of the product.

Ensure, if applicable, that any received amendment is

incorporated in the instructions. Hand over the Safety

and operating instructions if ever you lend, rent out or

sell the IBEX breaker.

All safety regulations listed in this manual comply

with the laws and regulations of the European

Union. Also observe the additional national/regional

regulations.

IBEX breaker operations outside the European Union

are subject to the laws and regulations valid in the

country of use. Please observe any other, more

stringent regional regulations and legislation.

Read the carrier manufacturer’s Safety and operating

Instructions before attaching the IBEX breaker to the

carrier and operating it. Observe all instructions.

1.1 Signal words

The signal words danger, warning, caution, and notice

are used as follows in this operation and maintenance

manual:

DANGER!

indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING!

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION!

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTE

The signal word NOTICE is used to address

practices related to possible property damage but

not related to personal injury.

1.2 Qualification

Transporting the IBEX breaker is only permitted if

carried out by people who:

◊ are authorised to operate a forklift truck

according to the applicable national provisions,

◊ know all the relevant national/regional safety

provisions and accident prevention rules,

◊ have read and understood the safety and

transport chapter of this operation and

maintenance manual.

Installing, maintaining, storing and disposing of

the IBEX breaker is only permitted if carried out by

people who:

◊ know all the relevant national/regional safety

provisions and accident prevention rules,

◊ have read and understood these Safety and

operating instructions.

◊ Operating the IBEX breaker is only permitted if

carried out by qualified operators. Operators are

qualified if they:

◊ have been trained to operate a carrier according

to the national regulations,

◊ know all the relevant national/regional safety

provisions and accident prevention rules,

◊ have read and understood these Safety and

operating instructions.

Testing the hydraulic installation is only permitted

if carried out by professionals.

Repairing the IBEX breaker is only permitted if

carried out by professionals trained by Dehaco.

1.3 Intended use

Only attach the IBEX breaker to a hydraulic carrier

of a suitable load−bearing capacity. Read the carrier

manufacturer’s instructions before attaching the

IBEX breaker to the carrier and operating it. Observe

all instructions.

Содержание IBEX 1200GS









































Результаты поиска

Содержание IBEX 1200GS

Отзывы:

Похожие инструкции для IBEX 1200GS

Бренды по названию

Популярные бренды

DEHACO IBEX 1200GS, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание IBEX 1200GS

Отзывы:

Похожие инструкции для IBEX 1200GS

Бренды по названию

Популярные бренды