Defro Home VITAL 37S, Руководство по эксплуатации

Страница: 19 / 52

19
o
Press the buttons.
o
Press the buttons causing switch to the other
modes
or .
7.7.9. PROGRAM MODE
The program mode allows setting fireplace operating times for
each day of the week. The heater switches on during operation when
ambient temperature is lower than set switch on temperature and it
switches off after reaching the switch off temperature.
Switch on temperature is the same temperature, which has been
set in the thermostatic mode. So, only switch off temperature and
operation times are configured after selection of the program mode.
Default values of temperatures:
Switch on temperature 21 ⁰ C,
Switch off temperature: ”--” (only control flame).
Switch on the mode using button, the following icons will
be shown on the display:
Temperature configuration:
o
Press and hold until the flashing icon will
be displayed. ON message and switch on
temperature will be displayed (temperature set in
thermostatic mode),
o
To set the switch off temperature, you should
press or wait a while . OFF message will be
displayed and temperature will flash.
o
Select required temperature with buttons.
o
Confirm the with button.
Configuration of operation times:
o
The ALL . message should flash on the display
after confirmation of switch off temperature.
o
Pressing selection keys, you can switch
between the days of the week:
ALL – one setting for all days
SA:SU – separate setting for
Saturday and Sunday
1 , 2 , 3 , 4 , 5 , 6 , 7 – separate settings
for each day of the week (Daily
Timer).
Confirm the selection with a key . The system waits for
configuration of switch on time in the next step.
Mode ALL
Configuration of program switch on time no. 1:
Icon and symbols 1, ON will be displayed, message ALL
will be shown for a while and hours field will flash.
Select switch on hour using the buttons
Confirm the hour with . ALL will be displayed once again
for a while and minutes field will be flashing.
Select minutes using buttons.
Confirm the setting once again with the button . The
system will go to configuration of switch off time.
Switch off time configuration:
o
The display will show, except the icon, 1 , OFF ,
message ALL and flashing hours field.
o
Select the hour with the selection buttons.
o
Confirm with button. ALL will be displayed
once again for a while and minutes field will be
flashing.
o
Set the minutes using buttons.
o
Confirm with button. The system will go to
configuration of program no. 2 in the same way as
for no. 1 .
If you want to avoid configuring program no. 2 - stop entering
the times and program no. 2 will remain inactive.
Mode SA:SU or Daily Timer
Switch on and switch off times are set in the same way as in
ALL mode
For SA:SU mode you set one switch on and switch off time
for both days at the same time.
In Daily Timer mode the unique switch on and switch off times
can be set for one, selected day, several days or for each day
of the week.
Notes!!!
Program no. 1 and no. 2 uses the same setting of switch on and
switch off temperature setting for each mode. Change of both
temperatures in thermostatic mode results in setting both these
values are new default values and they become switch on and
switch off temperatures for the programmed mode.
Configuration of the switch on and switch off times for the
Programs no. 1 and no. 2 causes that they will become new default
values. Restoring the factory settings for both programmes take
place after resetting the remote control by taking the batteries out.
7.7.10. ECO MODE
Press button to switch on Eco mode, an icon will be
shown on the display.
Press button once again to switch off the Eco mode.
7.7.11. BEHAVIOR OF FIREPLACE WHEN THERE IS NO SIGNAL
FROM THE REMOTE CONTROL
The flame will be automatically reduced to minimum level if there
is no command from remote control within six (6) hours. The control
system will shutdown the equipment and shut off the gas supply if the