manualshive.com logo in svg

DeDietrich DED700X, Руководство по обслуживанию, Страница: 7 / 51

Поделиться
Скачать
DeDietrich DED700X Скачать руководство пользователя страница 7

7 

 

 

 

2.2 Product 

technical 

data 

 

 

 

Power supply and consumption  

230 V~; 50 Hz; 1250 W 

120 V; 60 Hz; 1250W 

100 V; 60 Hz; 1250 W  

Safety devices  

Coffee boiler 2 175°C safety thermostats – steam boiler 175°C 

thermostat and 229°C heat fuse  

Temperature control  

NTC Sensor  

Coffee resistor  

Stainless steel heat exchanger - (1090W), for coffee or hot water.  

Steam resistor  

Aluminium tube heat exchanger - (1000W) for steam production (high 

speed steam production)  

Pump 

Ulka vibration pump; 

230V; 50 Hz; 48 W 
120V; 60 Hz; 41 W 

100V; 50/60 Hz; 55 W  

Safety relief valve  

Safety pressure relief valve with compensation valve  

Water filter 

Placed in the water tank  

Coffee grinder (grinding wheel)  

Threaded brass spindle, ceramic grinding wheels  

Motor  

DC 230 V / 120 V / 100 V  

Absorption  

During temperature rise : approx. 4.8 A (230 V); 

9 A (120V); 
11 A (100V)  

Absorption in energy-saving mode 

(stand-by)  

Approx. 20 Watt/h   

Main pump  

pressure 15 bar  

Dimensions LxWxH (in mm)  

595/325/458  

Weight 

Approx. 16 kg  

Coffee holder capacity (beans)  

Approx. 300 grams  

Water tank capacity  

Approx. 2 litres at the maximum level  

Heat exchanger volume  

Approx. 1.0 cm

3

 (10 ml volume)  

Water loading time  

Approx 10 seconds at start-up.  

Temperature rise time  

Approx. 1.5 minutes.  

Steam generation  

Immediate  

 

Содержание DED700X




















































Отзывы:

Нет отзывов