manualshive.com logo in svg

DeDietrich DED700X, Руководство по обслуживанию, Страница: 15 / 51

Поделиться
Скачать
DeDietrich DED700X Скачать руководство пользователя страница 15

15 

 

3.5  Outages displayed on the screen 

 

DISPLAYED OUTAGES

 

 

CAUSES/SOLUTIONS

 

GSI (water supply outage)  

- 

- 

Internal drip tray sensor 

Power  

PURGE 

- 

- 

Run water 

Check the water tank is correctly installed  

GROUP BLOCKED  

- 

- 

- 

Replace upper / lower micro-switch 

Power 

Small geared motor  

CLOSE THE PANEL  

- 

- 

- 
 

- 

Close the front panel 

Micro-switch 

Earthing of the machine disrupts the micro-switch 
Cut cables  

CLOSE THE DOOR  

- 

- 
- 

- 

- 

Close the front panel 

Micro-switch 
TRB support unhooked 

Door hinge bent 

Cut cables  

COFFEE GROUNDS TRAY MISSING  

- 
- 

- 

Put the coffee grounds tray back 
Micro-switch 

Cut cables  

GROUPE MISSING  

- 

- 

- 
- 

Put the group back 

Micro-switch 

Group flange broken 
Cut cables  

NOT ENOUGH COFFEE  

- 

- 

- 

Add coffee 

Replace PW 

Replace coffee griinder sensor  

DESCALE  

- 

- 

Descale 

Replace CPU  

GRINDER BLOCKED  

- 

- 

Replace the coffee grinder 

Replace PW  

FILL WATER TANK  

- 

- 

- 

Jammed floater 

Replace water sensor 

Replace PW  

FLASHING DISPLAY  

- 

- 

- 

Replace CPU 

Replace PW 

Crushed cables  

WAIT (does not heat) heat LEDs off  

- 

- 
- 

Reinitialise the thermostats 

Boiler cable disconnected 
Replace PW  

PART OF THE DISPLAY MISSING OR 

DISTORTED  

- 

- 

Replace the display 

Replace CPU  

NO STEAM  

- 

- 

Replace steam boiler 

Replace PW  

Содержание DED700X




















































Отзывы:

Нет отзывов