manualshive.com logo in svg

DeDietrich DED700X, Руководство по обслуживанию, Страница: 16 / 51

Поделиться
Скачать
DeDietrich DED700X Скачать руководство пользователя страница 16

16 

 

3.6  Checking micro-switches and sensors 

 

N°

 

Description

 

Activated

 

Deactivated

 

Notes

 

1  

Geared motor micro-

switch WORK  

Distributor in WORK 

position  

Distributor not in 

WORK position  

 

2  

Geared motor micro-

switch HOME  

Distributor in HOME 

position  

Distributor not in 

HOME position  

 

3  

Front command strip 

micro-switch  

Command strip closed  

Command strip 

open  

 

5  

COFFEE GROUNDS TRAY 

micro-switch  

Tray present  

Tray absent  

 

6  

DISTRIBUTION GROUP 

micro-switch  

Present  

Absent  

 

7  

DOOR Micro-switch  

Door closed  

Door open  

 

8  

FLOW METER  

 

 

The technician 

can check the 
impulses  

9  

COFFEE GRINDER 

IMPULSES  

 

 

The technician 

can check the 
impulses  

0  

WATER LEVEL in the 

tank  

Level is OK  

Level is LOW  

 

A  

WATER ALARM micro-

switch  

Water detected in the 

bottom of the machine  

No water detected 

in the bottom of the 
machine.  

 

M   Coffee holder empty  

There is no coffee  

There should be 
coffee.  

This is derived 
and not 

hardware data.  

R  

CLOCK (shows seconds)   Even seconds  

Odd seconds  

It should flash at  

1 HZ  

K  

FRONT FACE PRESENT  

Present  

Absent  

 

0-8   COFFEE GRINDER 

SETTINGS 

 

 

Factory settings  

*  

COFFEE GRINDER 

SETTINGS SAVED  

Not saved  

Saved  

 

 

Содержание DED700X




















































Отзывы:

Нет отзывов