DeDietrich DED700X Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 51

DeDietrich DED700X Скачать руководство пользователя страница 26

26

5.3 Aqua Prima

Operating logic with “AQUA PRIMA” filter

If the use of the “aqua prima” filter is selected from the user menu or the command strip, the system’s
water measuring logic becomes the following :

If the “aqua prima” function is

active

the electronics will count

one turbine impulse every two

revolutions.

If the “aqua prima” function is

inactive

the electronics will count turbine impulses

one impulse per

revolution.

A graph showing this function is shown below:

DESCALING

Hardness

Water hardness

Descaling frequency

Descaling frequency

when using Aqua Prima

1

Soft water (jusqu’à 7ºdH) Approx. 3 months 120 litres

Approx. 3 months 240 litres

2

Standard water
(7º-14ºdH)

Approx. 2 months 90 litres

Approx. 2 months 180 litres

3

Hard water (15º-21ºdH)

Approx. 6 weeks 60 litres

Approx. 6 weeks 120 litres

4

Hard water (15º-21ºdH)

Approx. 4 weeks 30 litres

Approx. 4 weeks 60 litres

«
...
24
25
26
27
28
...
»

Содержание DED700X




















































Отзывы:

Нет отзывов