Dean 1824 Скачать руководство пользователя

Страница: 42 / 46

24G SERIES FLATBOTTOM GAS FRYERS

CHAPTER 7: TROUBLESHOOTING

7-1

NOTE: Refer to the wiring diagram affixed inside the fryer cabinet door when
troubleshooting electrical components.

DANGER

Hot cooking oil/shortening will cause severe burns. Never attempt to move this appliance

when filled with hot cooking oil/shortening or to transfer hot cooking oil/shortening from one

container to another.

DANGER

This equipment should be unplugged when servicing, except when electrical circuit tests are

required. Use extreme care when performing such tests.

This appliance may have more than one electrical power supply connection point.

Disconnect all power cords before servicing.

Inspection, testing and repair of electrical components should be performed by an

authorized service agent only.

7.1 Pilot Burner Malfunctions

PROBLEM

CORRECTIVE ACTION

Pilot will not ignite; no
evidence of gas at pilot
burner.

1. Ensure the combination gas valve is in PILOT position and that

gas is available at the valve (check quick-disconnect and/or
gas-line connections).

2. Remove pilot gas supply line and check for obstructions. Blow

out with compressed air if necessary, then reinstall.

3. Check pilot burner orifice for obstructions.

Pilot burner ignites but
will not remain lit when
gas knob is released.

1. Check that the lead from the thermocouple is tightly screwed

into the pilotstat bushing on the gas control valve.

2. Remove end of thermocouple lead from pilotstat bushing and

clean with fine sandpaper. Ensure the bushing is clean.

3. Thermocouple possibly defective (millivolt output should be 12-

28mv); replace.

4. Pilot flame may be incorrectly adjusted. Adjust flame to 1-½"

high by turning pilot flow adjustment screw.

Содержание 1824















































Результаты поиска

Содержание 1824

Отзывы:

Похожие инструкции для 1824

Бренды по названию

Популярные бренды

Dean 1824, Руководство по установке и эксплуатации

Результаты поиска

Содержание 1824

Отзывы:

Похожие инструкции для 1824

Бренды по названию

Популярные бренды