manualshive.com logo in svg

DCS Proto-Sound 2.0 Diesel/Electric Locomotive Upgrade Kit, Руководство по установке, Страница: 16 / 44

Поделиться
Скачать
DCS Proto-Sound 2.0 Diesel/Electric Locomotive Upgrade Kit Скачать руководство пользователя страница 16

PS-2 Chassis Wiring Diagram

Notes:

1. For number board lights, use ditch or mars lights, whichever

is not being utilized in the locomotive.

2. If ditch lights are used as ditch lights, move ditch 2 to front

of the locomotive.

PS-2 Upgrade Kit Installation Guide

16

1

4

10
K

GROUND

PICKUP

SMOKE F

AN MOT

OR

(+)

(-)

SMOKE

HEA

T

ELEMENT

VOLUME POT

SMOKE SWITCH

T

ACH

READER

SMOKE UNIT

HARNESS

12-PIN CHASSIS

HARNESS

7-PIN CHASSIS

HARNESS

8-PIN CHASSIS

HARNESS

4 OHM, 3-W

AT
T

SPEAKER

SPEAKER (-)

SPEAKER (+)

OVERHEAD BEACON

MARKER LIGHTS - GREEN

DITCH LIGHT

#1

FRONT

PROT

O-COUPLER

CAB INTERIOR LIGHTS

FRONT

MARS LIGHT

FRONT

HEADLIGHT

WIRE NUT

MARKER LIGHTS - RED

DITCH LIGHT

#2

REAR PROT

O-COUPLER

REAR MARS LIGHT

REAR BACKUP

LIGHT

PS-2 CIRCUIT

BOARD

BA
TTER

Y
CHARGING JACK

AA

NICAD BA

TTER

Y
P

ACK

5-PIN MOT

OR

HARNESS

FRONT

MOT

OR

REAR

MOT

OR

(+)

(+)

(-)

(-)

GROUND

PICKUP

Содержание Proto-Sound 2.0 Diesel/Electric Locomotive Upgrade Kit













































Отзывы:

Нет отзывов