DCS Proto-Sound 2.0 Diesel/Electric Locomotive Upgrade Kit Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 44

DCS Proto-Sound 2.0 Diesel/Electric Locomotive Upgrade Kit Скачать руководство пользователя страница 12

Mounting The PS-2 Board

-Remove the PS-2 Board (A) from the

sealed anti-static bag

-Verify PS-2 board is securely inserted

into its plastic mounting bracket.

- Remove the speaker (H) from the

protective packaging

- Place the PS-2 board/plastic

mounting bracket (A) on the chassis
to verify the best location to
mount the plastic mounting bracket
and the metal heat sink bracket
(AA) to the chassis. Also locate
a place to put the battery pack (I)

And battery charging jack (II).

(NOTE: be

careful not to damage the speaker
cone).

NOTE: If you are not a
participating MTH
Authorized Service Center
there is NO warranty once
the bag is opened

NOTE: Use ESD safe work
area and procedures when
handling the PS-2 board.

Make sure the PS-2 board is firmly inserted
into the plastic mounting bracket. If not,
gently push the board into the bracket until
fully “captured” by the bracket. DO NOT
REMOVE THE BOARD FROM THE
BRACKET

.

Place the components on the chassis floor
in the best position given the space. It
may be necessary to turn the battery pack
on its side as seen above.

Position the battery pack close

enough to the PS-2 board so it does
require lengthening of the battery pack or
battery recharging port harnesses.
Lengthening either of these harnesses will
reduce the battery voltage to the board
and may affect operation.

Note:

NOT

PS-2 Upgrade Kit Installation Guide

12

«
...
10
11
12
13
14
...
»

Содержание Proto-Sound 2.0 Diesel/Electric Locomotive Upgrade Kit













































Отзывы:

Нет отзывов