manualshive.com logo in svg

DBA LaneWalker, Руководство по эксплуатации, Страница: 4 / 53

Поделиться
Скачать
DBA LaneWalker Скачать руководство пользователя страница 4

DBA LaneWalker Model C Operating Manual  

·

 Page 2

 

C. Care and Safety Procedures 

 
 

This machine is manufactured of the highest quality materials, but keep in mind that 

the DBA LaneWalker is a sensitive piece of equipment.  Care should be taken to see that it 
is not dropped, knocked around, or handled roughly.  Doing so may damage the 
programmable computer, its components, or the conditioner transfer system. 
 

 

For care and safety reasons, see that the following precautions are exercised: 

 

 

 

· AVOID SPILLING ANY LIQUIDS OR CHEMICALS INSIDE OF THE MACHINE 

 
 

· DO NOT OPERATE THE LANEWALKER WITH AN EXTENSION CORD OR 

 

  POWER CORD OTHER THAN THE ONE PROVIDED 

 
 

· DO NOT OPERATE THE LANEWALKER WITH POWER CORD SHUT-DOWN 

 

  SWITCHES DISCONNECTED 

 
 

· MAKE SURE THAT THE POWER OUTLET USED PROVIDES THE CORRECT 

 

  VOLTAGE AND AMPERAGE 

 
 

· DO NOT ATTEMPT TO MAKE ANY WIRING MODIFICATIONS 

 
 

· DO NOT ATTEMPT TO RE-PROGRAM THE COMPUTER 

 
 

· DO NOT OPERATE THE LANEWALKER IN AN UPRIGHT POSITION

 

 
 

Not following the above recommendations may cause damage to the LaneWalker, 

its computer, those persons operating it, or void the warranty. 
 
 

Persons assigned the responsibility of operating the DBA LaneWalker should be 

trained in its use by an authorized factory-trained Distributor.

 

Содержание LaneWalker






















































Отзывы:

Нет отзывов