DBA LaneWalker Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 53

DBA LaneWalker Скачать руководство пользователя страница 36

DBA LaneWalker Model C Operating Manual

·

Page 34

Section VII • DBA LaneWalker Maintenance Inspections

The following pages contain the suggested maintenance to be performed at 10, 50,

and 100 miles of operation. These inspections and adjustments are necessary so that the
DBA LaneWalker can operate in peak condition.

It is recommended that the operator check off the maintenance items as they are

completed for each inspection. Upon completion, the bowling center supervisor should
review the inspection with the operator, sign the form, and then clear the maintenance
message on the LaneWalker keypad.

Estimated time to complete each maintenance inspection is as follows:

10 Mile:

30 to 45 minutes

50 Mile:

45 minutes to 1 hour

100 Mile:

90 minutes to 2 hours

COMPLETE EVERY 10 MILES OF OPERATION

(Use special 50 and 100 Mile Checklist at Appropriate Times)

NOTICE TO LANEWALKER OPERATORS:

When the LaneWalker 10 Mile

Maintenance Inspection is due, please examine the entire machine thoroughly,
paying close attention to the items listed below on the 10 Mile Maintenance
Checklist. When your inspection and repairs are complete, review what has been
done with your Supervisor, then have him/her clear the Maintenance Message on
the LaneWalker keypad.

10

mile

20

mile

30

mile

40

mile

60

mile

70

mile

80

mile

90

mile

Clean entire machine thoroughly

Inspect lane to lane casters

Inspect lane to lane wheels

Inspect “hopping” wheels

Check all chain tensions

Remove wicks: inspect & clean
thoroughly with clean, dry cloth

Inspect wick cables, loops and
eye bolts for tightness and
proper operation

Operator’s Initials

Date

Actual Mileage

Supervisor’s Initials

Date

«
...
34
35
36
37
38
...
»

Содержание LaneWalker






















































Отзывы:

Нет отзывов