DBA LaneWalker Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 53

DBA LaneWalker Скачать руководство пользователя страница 19

DBA LaneWalker Model C Operating Manual

·

Page 17

When the LaneWalker is operated in the manual mode, a tachometer is available to

assist in adjusting the high and low speed settings of the drive motor. The tachometer
appears on the first line of the keypad screen during a continuous run.

When adjusting for low speed travel on the approach, the tachometer should read

between

42

and

46

. If the speed is set too slow, an error message may occur. If too fast,

crooked approach travel or pre-mature wheel wear may occur.

2. Lino Control Menu

Depress the

MENU

key until the following appears on the screen:

* LINO CTRL&RSET

0600 HIT MAN ENT

To reset the cloth counter, depress the

MAN

then

ENTER

keys while this screen is

displayed. Be certain to perform this procedure each time a new roll of duster cloth is
installed in the LaneWalker. When reset, the counter will read “0600”.

NOTE

:

If usable duster cloth still remains after counting down from “0600”, reset the

counter, then note how many additional lanes can be conditioned before cloth runs out.
After noting the additional lanes of cloth, access the SYSTEM CONTROL LINO DUSTER
Menu. Within this menu access the LINO EMPTY # LANES DEFAULT screen. By using
the Up or Down Arrow, change the default value to the correct number of lanes of cloth.

When this screen is displayed, the

UP

and

DOWN ARROWS

will

NOT

operate the

duster motors. A red push button on each Model C duster plate will operate the motor
when depressed. These buttons will work any time power is applied to the machine.

«
...
17
18
19
20
21
...
»

Содержание LaneWalker






















































Отзывы:

Нет отзывов